BEI Sensors HS35 Incremental Drawworks Encoder - Manual

BEI Sensors
Electrical Specifications
Code: Incremental
Output Format: 2 channels (A and B) in
quadrature ± 27° electrical, with index and
complements (see figure 1)
Cycles Per Shaft Turn: Up to 5,000 (see
Table A)
Supply Voltage: 5 or 9V
Current Requirements: 120mA (typical)
Output Device: 5V/OC, 9V/OC,
5V/OCR,40mA max current sink; 5 or 5V/V
line driver 100mA source/sink; 5V only
Frequency Response: 150kHz
Output Termination Pinouts: See Table 1
HS35 DrawWorks Ordering Options for assistance, call 800.350.2727
Use this diagram, working from left to right to construct your model number (example: HS35F-1-14-SS-200-ABZC-4469-SM18-EX-S)
All notes and tables referred to can be found on the back of this page.
HS35F SM18
S
SS
EN 55011 and EN 61000-6-2 CENELEC EEX ia IIC T4
U.S. Standards Class I, Group A,B,C & D;
Class II Group E, F & G Canadian Standards
Class I, Zone 0, Group IIC
Model HS35
DrawWorks Optical Encoder
This specially configured DrawWorks Model HS35 encoder combines rugged, heavy-duty
features into a unique through-shaft style for use as a winch-turns counter in the
DrawWorks system of oil rigs. It incorporates dual bearings and shaft seals for NEMA 4
and 13 (IP65) ratings, a hard-anodized metal housing and a sealed connector. It comes
with a standard 1”-14 diameter threaded connection and a convertible adapter that allows
its use in systems with a 5/8”-18 threaded connection. This encoder has an UL, cUL, and
ATEX/CENELEC intrinsically safe rating when installed with the proper barriers (refer to
BEI P/N 924-60004-XXX series on the back of this specification sheet). This barrier is
high performance, galvanically isolated and carries US and European agency approvals.
It is suitable for ALL Hazardous locations, regardless of gas and dust types.
Mechanical Specifications
Shaft Bore: 0.375” diameter through with
convertible adapter for 1” or 5/8” air coupler.
Starting Torque at 25°C: 7in-oz
Shaft Material: 416 stainless steel
Bearing Housing: Die cast aluminum
Bearing Life: 7.5 x10 9 revs (50,000 hrs at
2500 RPM)
Maximum RPM: 6,000 RPM (also see
frequency response)
Moment of Inertia: 0.019 oz-in-sec 2
Weight: Approximately 18 oz.
Environmental Specifications
Enclosure Rating: NEMA 4/13 (IP65)
Temperature: -40° to +80°C standard
Shock: 50 G/s for 11 msec duration
Vibration: 5 to 2000 Hz @ 20 G’s
Humidity: 98% RH without condensation
TYPE:
Hollow Shaft 3.5”
Diameter
THREADING:
1-14= 1” threaded bore
1-14L= 1” threaded bore
100-S= 1” straight bore
SHAFT SEAL:
SS= Shaft Seal
CYCLES PER TURN:
(Enter cycles) See
Table A
NO. OF CHANNELS:
A= Single Channel
AB= Dual Channel in Quadrature
ABZ= Dual Channel w/Index
AZ= Single Channel w/Index
COMPLEMENTS:
C= Complementary
outputs (5V/V)
OUTPUT IC:
5V/OC: (open collector)
9V/OC: (open collector)
5V/OCR: (open collector
with internal pull-
up resistor)
5V/V: (line driver)
CONNECTOR:
SM18= MS3102F18S-1P,
10 Pin Connector
INTRINSIC SAFETY:
EX= Intrinsically safe rated
encoder. Must be installed
with proper IS barriers
SPECIAL FEATURES:
For shaft insert assembly, add –S to model number
and specify one of the following P/N on your
Purchase Order.
31386-001: 1”-14 threads on both ends
31386-002: 1”-14 threads on female end, 5/8”-18
threads on male end
31386-003: 1”-14 threads on female end, 5/8”-18
threads on male end and adapter nut
Tel:805-968-0782 / 800-350-2727 | Fax: 805-968-3154 / 800-960-2726
7230 Hollister Ave., Goleta, CA 93117 | www.beisensors.com
Specification No. 02093-001 Rev. 06/11