BEI Sensors 8360 - Manual

8360 Series
360° Non-Contacting Through-Hole Position Sensor BEI Sensors
7230 Hollister Avenue
Goleta, CA 93117
www.beisensors.com
Tel: 800-350-2727
Fax: 805-968-3154
Rev 2-27-13
8360 Series
360° Non-Contacting Through-Hole Position Sensor BEI Sensors
The 8360 Series is BEI Sensors’ latest addition to the company’s line-up of robust, reliable,
and highly accurate non-contacting position sensors. The 8360’s low profile and through-
hole design make it desirable for applications like steering wheel and boom angle, where
space is limited and the sensor must mount around a shaft. The sensor’s dual analog output
is capable of resolving 360 degrees of motion with high accuracy and 12 bit resolution.
The 8360 Series provides IP65 sealing, 360 degree continuous rotation, a robust package
and wide operating temperature range, making it especially well suited for applications with
harsh environments like industrial vehicles, agricultural and construction equipment and
process controls. Non-contacting, redundant outputs provide the high reliability and long
life that are an absolute necessity in applications such as medical equipment or wind/solar
energy applications. A wide range of adaptations are available including PWM or Can Bus
output, shaft interface, electrical angle, connector type, cable length, output slope and much
more.
Ordering information FOR ASSISTANCE CALL 800-350-2727
SAMPLE: 8360075 (8360 Sensor with 75 Degrees Active Electrical Angle
Mechanical Specifications Electrical Specifications Environmental Specifications
Mechanical travel : travel 0° to +360° with no stops,
allowing for 360 degree continuous rotation
Actuation (starting) Torque : 0.2 N-m (28.5 oz-in)
Weight 220 grams max.
Rotational life : 10 million revolutions
Electrical angle : 15° to 360° in 15 degree increments
standard (other options available)
Input voltage : 5.0 V±0.25V DC
Input current : 16mA maximum per output
32mA maximum total (both channels)
Sensor Output : 0.25V – 4.75V for Analog at 5.0V input
Accuracy : +/- 0.6%
Resolution : 12 Bit, 0.088 degree
Environmental Sealing : IP65 standard
Electromagnetic compatibility : 100V/meter, 15kHz –
1GHz range
Vibration : 10 – 10,000 Hz, Total PSD: 4.94 Grms
Shock : 50Gs, half sine pulse, 11 m sec duration
Operating temperature range : -30°C to +85°C (wider
operating temperature -40° to +125 C° available)
Storage temperature range : -40°C to +105°C
8360XXX
*Standard Active Electrical Angles
015 = 15 degrees 195 = 195 degrees
030 = 30 degrees 210 = 210 degrees
045 = 45 degrees 225 = 225 degrees
060 = 60 degrees 240 = 240 degrees
075 = 75 degrees 255 = 255 degrees
090 = 90 degrees 270 = 270 degrees
105 = 105 degrees 285 = 285 degrees
120 = 120 degrees 300 = 300 degrees
135 = 135 degrees 315 = 315 degrees
150 = 150 degrees 330 = 330 degrees
165 = 165 degrees 345 = 345 degrees
180 = 180 degrees 360 = 360 degrees
Consult factory for options including:
• Non-standard output slope
• Clipped outputs
• Non-standard Active Electrical Angles
• PWM output (pulse width modulation)
• Special marking
• CAN Bus output
• Multi-turn
• Lead length
• Connector type
• IP67 sealing
• Shaft interface
Features
Non-contacting technology
Provides long life
Output signal choices
Analog, PWM, CAN Bus
Electrical angle
The standard version is available with rotational angles in 15 degree increments, up to 360°
Connector
Flying lead terminated w/6 pin AMP connector P/N 776434-1, contact P/N 1924463-1, other options
available
Through-hole design
Fits around shaft, shaft options available
Environmental
IP65-protected from dust and water jets
Operating temperature
-30° to +85°C standard, (option for -40°C to +125°C)
Electrical protection
Overvoltage, short circuit, ESD
Magnetic Shielding to 20G