BEI Sensors SwiftComm® Real-Time Wireless Encoder Interface - Manual

These commodities, technology or software if exported from the United States must be in accordance with the Bureau of Industry, and Security, Export Administration regulations. Diversion contrary to U.S law is prohibited.
SwiftComm
™
Wireless Incremental Interface
SenSor Type:
IN = Incremental Encoder
MounTing:
PM1 = 2, 1/4–20 tapped holes
ouTpuT volTage
FroM SenSor:
5 = 5 VDC, 15 = 12-15 VDC
24 = 24 VDC
inpuT TerMinaTion:
SCS120-M18 = 10’ Cable Assy
SCS120-M12 = 10’ Cable Assy
SCS120 = 10’ Pigtail
Varying cable length available, consult factory
SenSor Type:
IN = Incremental Encoder
MounTing:
PM1 = 2, 1/4 – 20 tapped holes
ouTpuT Type:
28V/V = 5-28Vin/out
28V/5 = 5-28Vin/5Vout
28V/OC = 5-28Vin/OCout
ouTpuT
TerMinaTion:
M18 = MS3101F18-1P
SwiftComm ordering options
for assistance call 800-350-2727
Order Note: The Transmitter and Receiver are sold as pairs. Sensor type must be the same for Transmitter and Receiver modules
TranSMiTTer Model nuMber
reCeiver Model nuMber
TX in pM1
rX in pM1 M18
SCS120-M18
Receiver includes antenna. Mating cable assemblies are available.
Transmitter includes antenna and pigtail or connector
assembly. Power cable ordered separately.
Now the machine designer is free to install
sensor equipment without the expense and
constraints of a hard-wired system. Encoder
installations in difficult applications like cranes,
rotating tables or mobile applications, are
greatly simplified. The SwiftComm system
includes the transmitter-receiver pair, which
communicates using a point-to-point frequen-
cy-hopping 2.4 GHz RF protocol. Because of its
flexible input/output electronics, it can interface
with many different industrial sensors and
control systems. Simply connect the SwiftComm transmitter to the sensor and
the SwiftComm receiver to your control system and apply power. That’s it! No
complicated cabling required.
SwiftComm’s proprietary radio protocols include a broad security code range,
data encryption, handshaking, interference recovery, and error checking that
together provides a secure and robust wireless interface system. Ruggedness
and flexibility are further enhanced with SwiftComm’s NEMA 4 weatherproof
enclosures, panel mounting options, antenna choices and wide-range DC
power inputs.
Tel: 805-968-0782 /800-350-2727
Fax: 805-968-3154 / 800-960-2726
7230 Hollister Ave., Goleta, CA 93117-2807
www.beisensors.com
• Robust Signal
• Real-Time Control
• Secure Transmission
• Long Range
SwiftComm’s unique advantages
electrical Specifications
Supply voltage (transmitter or receiver):
5 to 28 VDC (see model number)
Supply Current (transmitter or receiver):
220 mA Max
output Format:
Transmitter Input: 2 Channels in quadrature,
1/2 cycle index gated w/ negative B channel
Receiver Output: 2 Channels in quadrature,
cycle index gated w/ negative B channel
Temperature: Operating: -40° to 70°,
Storage: -40° to 100°
rf Specifications
rF power output: 17 dBm (50 mW) Nominal
Frequency range: 2.4 GHz ISM Band
Adaptive Frequency Hopping Protocol
Sensitivity: -80 dBm (0.1% BER @
1000kbps)
antenna Connector: TNC – Reverse Polarity
(50 Ohm)
Transmission range: 300 Meters (5.5 dBi
Gain “Rubber Duck” Swivel Antenna, antenna
mounted directly to enclosure)
encryption: Proprietary enhanced 40-bit
encryption with pseudo-random frequency hop-
ping sequence.
Security Codes: 5 Byte range (>500 billion
unique codes)
output Specifications
Frequency response: > 500 KHz
link update rate: 600 uS
Signal loss Time without link Failure:
120 mS
Transmission response Time: 1ms typical
Mechanical Specifications
dimensions: (mm, including Antenna Connector)
Transmitter (excluding cable set): 75W x 98L x 53H
Receiver: 75W x 119L x 53H
Weight:
Transmitter with 10-foot cable (no antenna):
911 grams
Receiver (no antenna): 455 grams
enclosure: NEMA 4 cast aluminum, powder
coated, gasketed closure intended for indoor or
outdoor use. Protected against windblown dust
and rain, splashing water, hose directed water
and by the formation of ice on the enclosure.
Mounting options: Two 1/4 - 20 tapped
holes on back of enclosure for mounting to
flat surface. Optional mounting ears or DIN
rail kit available.
Specification No. 02107-001 Rev.11-11
a whole
new era in
wireless
industrial
control