Draw-Tite 75054 MAX-FRAME RECEIVER - Manual (Page 2)

NUT
1/4 X 1-1/2 X 2 BLOCK (3719)
1/2-13 X 1-3/4 GR5
CARRIAGE BOLT
EXISTING WELD NUT BAR BOTH SIDES
WITH CLOSED SIDED SKID SHIELD.
EXISTING DRIVER'S SIDE ONLY WITH
TOW HOOK.
CARRIAGE BOLT
1/2-13 X 1-3/4 GR5
1/4 X 1-1/2 X 2 BLOCK (1277)
NUT
FIGURE 3
OPTION C PASSENGER SIDE ONLY
OPTION D
FRAME RAIL
EXISTING M12 BOLT
1/2 FLAT WASHER (2)
USED AS SPACERS
STEEL SKID SHIELD
FRAME RAIL
OPTION B DRIVER'S SIDE ONLY
OPTION A
FIGURE 2
CLOSED SIDED
FISHWIRE THROUGH END OF FRAME
NOTE: LEAVE FISHWIRES ATTACHED
TO CARRIAGE BOLTS UNTIL LOCK
WASHERS AND NUTS ARE INSTALLED.
THIS WILL ALLOW BOLTS TO BE
PULLED THROUGH RECEIVER AFTER
RECEIVER IS POSITIONED AROUND
FUEL TANK.
JEEP CHEROKEE
JEEP WAGONEER
(DOWNSIZED MODEL)
75054
CONICAL WASHER
M12 X 1.75 X 40mm CL8.8
CONICAL WASHER
CONICAL WASHER
INSTALLATION INSTRUCTIONS
OPTION B
FIGURE 5
EXISTING WELD NUT BAR BOTH SIDES
WITH CLOSED SIDED SKID SHIELD.
HARDENED FLAT WASHER
M12 X 1.75 X 40mm CL8.8
LOCK WASHER
1996 AND EARLIER
VEHICLES
M12 X 1.75 X 40mm CL8.8
M12 X 1.75 X 40mm CL8.8
LOCK WASHER
HARDENED FLAT WASHER
CONICAL WASHER
1997 AND LATER
STEEL SKID SHIELD
VEHICLES
CLOSED SIDED
NOTE: CLOSED SIDED STEEL SKID
SHIELD IS BETWEEN FRAME
RAIL AND RECEIVER.
FRAME RAIL
EXISTING M12 BOLT
DO NOT REMOVE
SKID SHIELD MUST BE DRILLED,
DO NOT DAMAGE WELDNUT.
33002
NOTE:Check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is
removed, plug all holes in trunk pan or other body panels to prevent entry of water and exhaust fumes. A
hitch or ball which has been damaged should be removed and replaced. Observe safety precautions
when working beneath a vehicle and wear eye protection. Follow car maker's specs for maximum trailer
weight and tongue weight. Do not cut access or attachment holes with a torch.
APPROX WEIGHT (LB.)
when working beneath a vehicle and wear eye protection. Follow car maker's specs for maximum trailer
hitch or ball which has been damaged should be removed and replaced. Observe safety precautions
removed, plug all holes in trunk pan or other body panels to prevent entry of water and exhaust fumes. A
Check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is
weight and tongue weight. Do not cut access or attachment holes with a torch.
NOTE:
APPROX WEIGHT (LB.)
VEHICLE HITCH NO.
2002 Towing Products
2 2 12/05/07
SHEET OF c
35.5 01130-878
FASTENER KIT
Plymouth, Michigan
VIEWED FROM UNDER VEHICLE LOOKING UP
FIGURE 4
BLOCK (3719) - 2 PLACES
HANGER STUD AND NUT
HANGER STUD AND NUT
OPTION E - EXHAUST
OPTION D - EXHAUST
NOTE: PROPER ORIENTATION OF BLOCKS IS NECESSARY
1/4 X 1-1/2 X 2
BLOCK (3719) - 2 PLACES
BLOCK (1277) - 2 PLACES
1/4 X 1-1/2 X 2
1/2" HANDLE NUT
VEHICLE
OF
REAR FRAME RAIL
PASSENGER'S
SIDE
FRAME RAIL
SIDE
DRIVER'S
TO INSURE FASTENER ALIGNMENT
2 PLACES
1/4 X 1-1/2 X 2
HANDLE NUT
1/2-13 X 1-3/4 GR5
LOCK WASHER
87591