Draw-Tite 75690 MAX-FRAME RECEIVER - Manual

Installation Instructions
Honda CR-V
Part Numbers:
44643
75690
87578
Do Not Exceed Lower of Towing Vehicle
Manufacturer’s Rating or
Fascia
Hitch Shown In Proper Position
Equipment Required: Pull Wire (Provided)
W h 11/16” 7/8”
Fastener Kit: 75690F
Manufacturer s Rating or
Hitch type
Max Gross
Trailer WT (LB)
Max Tongue
WT (LB)
Weight Distributing Do Not Use With Spring Bars
Weight Carrying
Ball Mount
3,500 (1589 Kg.) 350 (159 Kg.)
Wiring Access Location: SUV3
Wrenches: 11/16”, 7/8”
Drill Bits: None
A. Insert bolt and
block into frame
B. Align block on
access hole
C. Pull bolt thru
block
Figure 3
Fishwiring Procedure 1
Figure 2
Kink pull wire to keep
Block independent
of bolt
56
Typical
Both Sides
1
Qty. (1) U-Bolt 3/8-16
5
Qty. (4) Carriage Bolt ½-13 x 1.25 GR5
Figure 1
234
78
Typical Both Sides
Enlarge this hole to
allow fishwiring
Both Sides
1. Lower exhaust by disconnecting rubber exhaust hangers from exhaust, two places rear of muffler and one place forward of muffler, near rear axle.
Bend the exhaust hanger pins to lower exhaust ½”.
Note: Rubber exhaust hanger must be attached to hanger rod welded on vehicle frame before hitch is installed. Hitch side bracket will prevent
access to hanger rod after installation Therefore it is recommended to remove rubber exhaust hanger from muffler end instead
2
Qty. (2) Flat Washer 3/8”
6
Qty. (4) Spacer Block ¼ X 1 X 3
3
Qty. (2) Lock Washer 3/8”
7
Qty. (4) Conical Toothed Washer ½”
4
Qty. (2) Hex Nut 3/8-16
8
Qty. (4) Hex Nut ½-13
access to hanger rod after installation. Therefore, it is recommended to remove rubber exhaust hanger from muffler end instead.
2. If necessary, enlarge forward access hole, each side, to allow fishwiring of carriage bolt and spacer block.
3. Fishwire ½-13 carriage bolt and spacer block through access holes and down through rearward hole, both sides of vehicle.
4. Fishwire ½-13 carriage bolt and spacer block through access hole and back down through same hole (see figure 2)
5. Raise hitch into position, being careful not to push fasteners back into frame. Loosely install conical toothed washers and nuts.
6. Center hitch on vehicle and install U-Bolt as shown in Figure 1. Install flat washers, lock washers and nuts onto U-Bolt.
7. Tighten all fasteners to torque specs below.
8. Raise exhaust back into position and re-attach rubber exhaust hangers, 3 places, as removed in step 1
Ti ht ll ½ 13 GR5 f t ith t h t 75 Lb Ft (102 N*M)
Tighten all 3/8-16 GR5 fasteners with torque wrench to 30 Lb.-Ft. (41 N*M)
z 2010 Cequent Performance Products Sheet 1 of 3 75690N 4-26-10 Rev. B
Tighten all ½-13 GR5 fasteners with torque wrench to 75 Lb.-Ft. (102 N*M)
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent
entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working beneath a
vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and
SAE J684.
Form: F205 Rev A 5-6-05