Draw-Tite 24880 SPORTFRAME HITCH - Manual

Installation Instructions
VOLKSWAGEN PASSAT
Lower fascia panel will need to be trimmed
Part Numbers:
Hitch Shown In Proper Position
Wiring Access Location: PC3 & 4 Equipment Required: Tape, Utility Knife or cutting wheel,
Tape Measure & Marking Pencil, Silicone sealant.
Wrenches: 15 torxbit, 25 torxbit, 10mm,
13mm, ¾” socket,
Drill Bits: ¼ if needed
Trunk pan
Do Not Exceed Lower of Towing Vehicle
Manufacturer’s Rating or
Drawbar must be used in the
RISE position only.
Drawbar Kit:
3590
Fastener Kit: 24880F
24880
60297
77267
2000 LB (908 Kg) Max Gross Trailer Weight
200 LB (90.8 Kg) Max Tongue Weight
Fascia
Bumper
rail
Recomemend ¼” drill in
corners
1 1 1 1
2-1/2” 2-1/2”
5”
Bumper rail
Loosen or remove the
lower fascia panel – using
a small screwdriver insert
in top of slot and gently
twist
2 2 2 2
3 3 3 3
4 4 4 4
5 5 5 5
3 3 3 3
1. Remove spare tire from vehicle. Remove the (2) rearward drain plugs and return to owner.
2. If present remove the appearance panel on the passenger side. DO NOT REMOVE CANISTER ON DIESEL MODELS.
3. Remove the (3) torx screws and clips.
4. Lower exhaust by removing the (2) hex bolts at the exhaust hanger.
5. Loosen or remove the lower fascia panel – using a small screwdriver insert in top of slot and gently twist as you gently apply pressure. See Figure 2.
6. Trim lower fascia panel as shown in Figure 1. Lay out the area to be trimmed by marking with tape or marking pencil (recommend drilling ¼” minimal
holes in corners).
7. Place the bolt plates on top of the bumper rails (as shown).
8. Raise hitch into position. If, lower appearance panel not completely removed slide under the passenger side all the way over until you have the
clearance to raise the drivers side into position ( hitch must be raise over existing facial tabs.
9. Install the hex bolts and conical washers into the bolt plate. Do not completely tighten.
10. Install the carriage bolts and spacer into the trunk drain holes. Use silicone sealant on the bolt plate to assure a seal.
11. Seal around the bar at the trunk pan connection and install the conical washer and hex nut.
12. Tighten all fasteners to the required torque specification.
13. Reinstall the lower fascia panel (line up slot and gently push back into position). Reinstall (2) torx screws and clips. Reinstall the apperance panel if
removed.
14. Reinstall exhaust.
15. Place spare tire back into trunk .
©
2012 Cequent Performance Products, Inc Sheet 1 of 3 24880N 1-13-12 Rev. A
1 1 1 1 Qty. (2) Bolt plate 4 4 4 4 Qty. (2) Carriage bolt ½-13 X 1.75 GR5
2 2 2 2 Qty. (4) Hex bolt ½-13 X 5.50 GR5 5 5 5 5 Qty. (2) Spacer
3 3 3 3 Qty. (6) Conical washer ½” 6 6 6 6 Qty. (2) Hex nut ½-13
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent
entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working beneath a
vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and
SAE J684.
Form F206 Rev A 5605
Note: Fasteners typical both sides
Tighten all ½” fasteners with torque wrench to 75 Lb.-Ft. (102 N*M)
Center fascia tab location.
Figure 1.
Figure 2.
Figure 3.
6 6 6 6
3 3 3 3