Draw-Tite 118265 OEM WIRING HARNESS - Manual

ENGLISH
TOOLS REQUIRED:
Trim Panel Remover, Test-probe
1. Locate the two black relays (included).
Insert the two relays into the black connector
on the included relay and fuse harness.
NOTE
The use of relays that differ from the relays
included can result in the unit not to function
or may damage the vehicle and or trailer.
2. Open rear door and push forward the rear seat
d
. On the driver's side, using a trim panel
remover. Carefully remove the compartment
door labeled "AUX FUSE"
ef
.
3. Locate the vehicle’s white trailer tow plug, located
behind the trim panel removed in step 2 g .
4. Locate a flat surface in an out of the way place
and mount the T-Connector’s black box-module,
to prevent damage or rattling.
NOTE
This surface should be in an area that is free of
any moisture and mounted in an area that it is
high enough where it could not be exposed to
direct contact with any water or liquid substance.
WARNING
The black box-module is intended to be mounted
ONLY in the INTERIOR of the vehicle. Mounting
on the exterior or areas exposed to the elements
or moisture could cause serious damage to
the vehicle and module. Secure the remainder
of the T-Connector harness with the cable ties
provided, to prevent damage or rattling and
being careful to avoid any areas that would
pinch, cut or melt the wire.
5. Locate vehicle fuse box in engine compartment
on driver's side. Insert fuses into positions
as shown
hi
.
6. Locate the large grey housing under the
vehicle bumper on the driver’ side. Remove
protective cap, being careful not to break the
locking tabs. Ensure that the mating surfaces
are free of dirt. Plug towing harness into
grey tow plug. Be careful not to damage
the locking tabs and be sure that connectors
are fully inserted with locking tabs in place.
Route the T-Connector harness rearward to
the back of the fascia of the bumper
j
.
WARNING
Route the wire being careful to avoid any
hot pipes, heat shields, the fuel tank or any
other points that may pinch or break the wire.
7. Secure 7-Way tow harness to hitch.
Bracket not included.
WARNING
Secure the remainder of the T-Connector
harness under the bumper with cable ties
provided, being careful to avoid any areas
that would cut or pinch the wire.
WARNING
All connections must be complete for the
T-Connector to function properly. Test and
verify installation with a test light or trailer
once installed. For initial test, reset vehicle
electrical system by temporarily removing
the key from the ignition.
8. Reinstall, access door, rear cargo door and
other items removed during installation,
being careful not to pinch or cut the wires.
WARNING
Overloading circuit can cause fires. DO NOT
exceed lower of vehicle manufacturer rating or:
• Max. stop/turn light: 2 per side (4.2 amps)
• Max. tail lights: (15 amps)
• Max. backup: (7.5 amps)
• Max. power circuit: (15 amps)
• Max. trailer brakes: 3 Axles/6 brakes (18 amps)
Read vehicle's owners manual & instruction
sheet for additional information.
Installation Instructions
Directives de Montage
Instrucciones de Instalación
T-Connector
Connecteur en T
Conector en T
Honda Pilot
j
d
e
g
f
i
h
118265-037 Rev. B 5/24/2013
READ THIS FIRST:
Read and follow all vehicle warnings and installation
instructions before beginning installation. Wear safety
glasses and use all safety precautions during installation.
LISEz CECI EN PREMIER:
Lire et observer toutes les consignes de sécurité et les
instructions avant de commencer l’installation. Durant
l’installation, veiller à toujours porter des lunettes de
protection et respecter les mesures de sécurité.
LEA ESTO PRIMERO:
Lea y siga todas las advertencias e instrucciones de
instalación del vehículo antes de empezar la instalación.
Use gafas de seguridad y todas las precauciones de
seguridad durante la instalación.