Installation instructions, Part numbers, Figure 2b – Draw-Tite 4448 GOOSENECK RAIL KIT User Manual

Page 2: Figure 2c figure 2d, Figure 2a, Figure 3

Advertising
background image

Installation Instructions

Part Numbers:

4448

NOTES:

¾

This rail kit can be used with a 9460 or 9470 head only.

¾

Al

k

th b ll i f ll l

k d b f

t

i

GOOSENECK MOUNTING KIT

Ford F-250/F-350 Super Duty

Will not fit Cab-on-Chassis vehicles

¾

Always make sure the ball is fully locked before towing.

¾

Keep the ball and ball sleeve well lubricated.

¾

Periodically re-torque all the hitch fasteners.

¾

Check ball, hitch coupler, safety chains and other connections for proper operation every time you tow.

Warning:
™

The tow vehicle manufacturers recommended towing capacities should UNDER NO CIRCUMSTANCES be exceeded.

™

Check for adequate clearance between the gooseneck trailer and the rear of the cab and the rear of the truck box before installing hitch.

™

All trucks have fuel lines, brake lines and electrical wiring located along the vehicle frame where the rail kit installs. Carefully examine the
location of fuel lines, brake lines and electrical wires before installation and be certain not to damage these when positioning the hitch
components Be careful when drilling holes cutting sheet metal and tightening fasteners as to not limit the integrity of these systems

components. Be careful when drilling holes, cutting sheet metal and tightening fasteners as to not limit the integrity of these systems.

Hide-A-Goose Installation Instructions
1.

Lower the vehicle exhaust.

2.

Use the provided cable tie to relocate the lines connected to the bracket on the driver’s side of the vehicle, shown in Figure 2a.

2b.

On Gas Engine Vehicles Only. The vapor tube running along the inside of the driver’s side frame rail must be relocated

prior to installing the driver’s side bracket (see Figure 2b). Remove the flange nut from the outside of the frame and keep for

Hide-A-Goose Only – Drilled hole in bed location (see step 8).

Short Box & Long Box – 46-3/16 inches

p

g

(

g

)

g

p

later use (see Figure 2c). Rotate the tubes up and out of the way. Install the L-bracket with 1/4” hardware, as shown in

Figure 2d. Tighten the L-bracket to the frame, but leave the tube holder loose to aid bracket installation. The tube holder will

be tightened onto the L-bracket in Step 12.

Driver’s side
frame rail

Driver’s side
frame rail

Existing

flange nut

11

12

11

10

Fuel Tank

Relocate Lines

3.

Place 5/8” GR8 carriage bolts from the 9460/9470 fastener kit into the square holes on the forward and rearward cross

members from the top pointing towards the ground. The forward cross member has two additional holes (see figure 3).

4.

From underneath the vehicle, install the rearward hitch cross member by placing one end above the vehicle frame and

Vapor
tube

Tube
holder

Figure 2b

Inside of frame rail

Figure 2c

Figure 2d

L-bracket

Existing
flange nut

Figure 2a

F

r

a

F

r

a

Front Hat Channel

maneuvering the notched section of the opposite end, above the vehicle frame. Temporarily position the rearward hitch cross

member against the rear hat channel of the vehicle.

5.

From underneath the vehicle install the forward hitch cross member by placing the driver’s side notched end above the

vehicle frame and maneuvering the opposite notched end above the exhaust and above the vehicle frame.

F

r

a

F

r

a

Front Hat Channel

Additional

Holes

a
m
e

a
m
e

Rear Hat Channel

z

2010 Cequent Performance Products

Sheet 2 of 8

4448N

3-22-10

Rev. A

a
m
e

a
m
e

Rear Hat Channel

Rear Cross Member

Installation

Forward Cross Member

Installation

Figure 3

Carriage

Bolts

Carriage

Bolts

Advertising