Draw-Tite 118443 T-ONE CONNECTOR - Manual

•
i
118443-037 Rev. A 08/02/07
ENGLISH
TOOLS NEEDED:
Trim Panel Remover, 10mm Socket &
Ratchet or 10mm Wrench, Drill (3/32” Drill Bit),
1/4” socket, Torx-45, Torx-30, Philips Head
Screwdriver, Test-probe
1. Open the rear lift gate. Remove threshold plate, trunk
floor panels and spare tire tray from vehicle
d .
Remove cargo loops e-1 , phillips head screws
e-2 , and the sliders and screws from the side rails
e-3 & e-4 so that the driver’s side trim panel can
be carefully pulled away from the vehicle e .
2. On the driver’s side of the vehicle, remove the
fasteners that hold the black Styrofoam tray and
carefully pry the black Styrofoam tray out
f .
3. Locate the plastic side pocket inside of the driver’s
side trim panel
g .Using the panel puller, slowly
pry up the tray until it pops out of the panel.
4. On the passenger side, locate a small opening beneath
the Styrofoam pad
h . Reach in and pry the plastic
side pocket up out of the trim panel.
5. On the driver and passenger sides of the vehicle,
locate the vehicles' taillight wiring harness (inside
the panel where the plastic trays have been removed)
g . The taillight wiring harness will have a connection
point, on both sides, matching the ends of the
T-Connector. Separate this connector, being careful
not to break the locking tabs. All connector surfaces
should be clean and free of dirt.
6. On the passenger side, insert the T-Connector end,
with the green wire, between the vehicle wiring
connectors and lock into place. Be sure that
connectors are fully inserted with locking tabs in place.
7. On the passenger’s side route the T-Connector end
with the yellow wire through the trim panel access
hole, across the threshold, & through the drivers trim
panel access hole. Repeat step 6 for the driver’s side
using the T-Connector harness end with the
yellow wire.
8. On the passenger’s side, locate existing ground
stud inside the trim panel. Loosen the nut, place
T-Connector white wire with ring terminal on stud
and retighten the nut, making sure that all existing
ground connections are still attached.
9. Route the black wire into the engine compartment
up to the battery
i .
WARNING
Route the wire being careful to avoid any hot pipes,
heat shields, the fuel tank or any other points that
may pinch or break the wire.
10. Disconnect the vehicle’s Negative (-) battery cable.
If not removed, remove the fuse from the yellow
fuse holder (provided). After cutting the fuse holder
wire
j , attach the ring terminal and secure to the
vehicle’s Positive (+) battery cable k . Connect the
other end of the fuse holder to the black 12 ga.
wire, using the yellow butt connector (provided).
11. Reconnect the vehicle’s Negative (-) battery cable
and install the 10 amp fuse into the fuse holder
from step 10.
WARNING
All connections must be complete for the
T-Connector to function properly. Test and verify
installation with a test light or trailer once installed.
12. Mount the T-Connector black box using
double-sided tape provided. Secure the remainder
of the T-Connector harness with the cable ties
provided, to prevent damage or rattling and
being careful to avoid any areas that would
pinch, cut or melt the wire.
13. Reposition passenger side panels, trays and
trunk floor panels and reattach the threshold.
NOTE
Store 4-Flat in rear cargo area when not in use.
WARNING
Overloading circuit can cause fires. DO NOT exceed
lower of towing manufacturer rating or:
• Max. stop/turn light: 1 per side (2.1 amps)
• Max. tail lights: (4.2 amps)
Read vehicle’s owners manual & instruction sheet
for additional information.
•
f
•
j
•
g
•
h
•
k
•
d
•
e
Installation Instructions
Directives de Montage
Instrucciones de Instalación
T-Connector
Connecteur en T
Conector en T
READ THIS FIRST:
Read and follow all vehicle warnings and installation instructions
before beginning installation. Wear safety glasses and use all
safety precautions during installation.
LISEZ CECI EN PREMIER:
Lire et observer toutes les consignes de sécurité et les instruc-
tions avant de commencer l’installation. Durant l’installation,
veiller à toujours porter des lunettes de protection et respecter
les mesures de sécurité.
LEA ESTO PRIMERO:
Lea y siga todas las advertencias e instrucciones de instalación
del vehículo antes de empezar la instalación. Use gafas de
seguridad y todas las precauciones de seguridad durante
la instalación.
e-2
e-1
e-3
e-4