Draw-Tite 118536 T-ONE CONNECTOR - Manual

i
9. Reconnect the vehicle’s Negative (-) battery
cable and install the 15 amp fuse into the fuse
holder from step 7.
WARNING
All connections must be complete for the Trailer
Tow Harness to function properly. Test and
verify installation with a test light or trailer once
installed. For initial test, reset vehicle electrical
system by temporarily removing the key from
the ignition.
10. On the Driver’s side, mount the T-Connector
black box using the double-sided tape provided.
Secure the remainder of the T-Connector harness
with the cable ties provided, to prevent damage
or rattling and being careful to avoid any areas
that would cut or pinch the wire.
WARNING
Make sure module is mounted so that the
epoxy side of the module is pointed towards
the ground to prevent any water buildup.
11. Reinstall the taillight housing assemblies,
positioning the vehicle wiring harness
between the housing and the vehicle body.
12. Mount the 4-Flat end in an accessible location
with a bracket or electrical box (not included).
WARNING
Overloading circuit can cause fires. DO NOT
exceed lower of vehicle manufacturer rating or:
• Max. stop/turn light: 2 per side (4.2 amps)
• Max. tail lights: (7.5 amps)
Read vehicle’s owners manual & instruction
sheet for additional information.
ENGLISH
TOOLS REQUIRED:
Trim Panel Remover, Drill (3/32” Drill Bit),
Philips Head Screwdriver, Test-probe
1. Open the tailgate and remove the vehicle’s
right side taillight assembly by removing the two
clips holding the taillight in place. Carefully pry
the housing away from the vehicle, being careful
not to break the alignment tabs. Repeat for the
vehicle’s left side taillight assembly de.
2. On the driver and passenger sides of the
vehicle, locate the vehicle’s taillight wiring
harness. The taillight wiring harness will have
a connection point, on both sides, matching
the ends of the T-Connector. Separate this
connector, being careful not to break the
locking tabs. All connector surfaces should
be clean and free of dirt f.
3. On the driver’s side, insert the T-Connector
end, with the yellow wire, between the vehicle
wiring connectors and lock into place. On the
driver’s side, insert the T-Connector end, with
the brown and red wire, between the vehicle
wiring connectors and lock into place. Be careful
not to damage the locking tabs and be sure that
connectors are fully inserted with locking tabs
in place f.
4. Route the harness containing the green wire
and the 4-Flat down the opening behind the
taillight on the driver’s side. Route the 4-Flat
harness underneath and to the center of the
vehicle. Route harness containing the green
wire underneath the vehicle up through the
opening behind the passenger’s side taillight f.
WARNING
Route the wire being careful to avoid any
hot pipes, heat shields, the fuel tank or any
other points that may pinch or break the wire.
5. Repeat step 3 for the passenger’s side using
the T-Connector containing the green wire.
6. Locate a suitable grounding point on the driver’s
side near the connectors. Drill a 3/32” hole
and secure white wire with eyelet using screw
provided. Do not drill into any exposed surfaces.
CAUTION
Verify what is behind any surface prior to drilling
to avoid damage to the vehicle and/or personal
injury. Do not drill into any exposed surfaces.
7. Disconnect the vehicle’s Negative (-) battery
cable. If not removed, remove the fuse from
the yellow fuse holder (provided). After cutting
the fuse holder wire g, attach the ring terminal
and secure to the vehicle’s Positive (+) battery
cable h. Connect the other end of the fuse
holder to the black 12 ga. wire, using the yellow
butt connector (provided).
WARNING
Read and follow all warnings and cautions
printed on the tow vehicle’s battery.
8. Route the black wire out of the engine
compartment and to the rear driver’s side of
the vehicle i. Connect the other end of the
black 12 ga. wire to the red power wire located
on the T-Connector’s black box, using the
yellow butt connector (provided).
WARNING
Route the wire being careful to avoid any
hot pipes, heat shields, the fuel tank or any
other points that may pinch or break the wire.
118536-037 Rev. A 7/24/2012
Installation Instructions
Directives de Montage
Instrucciones de Instalación
T-Connector
Connecteur en T
Conector en T
Dodge Journey
e
f
g
h
d
READ THIS FIRST:
Read and follow all vehicle warnings and installation
instructions before beginning installation. Wear safety
glasses and use all safety precautions during installation.
LISEz CECI EN PREMIER:
Lire et observer toutes les consignes de sécurité et les
instructions avant de commencer l’installation. Durant
l’installation, veiller à toujours porter des lunettes de
protection et respecter les mesures de sécurité.
LEA ESTO PRIMERO:
Lea y siga todas las advertencias e instrucciones de
instalación del vehículo antes de empezar la instalación.
Use gafas de seguridad y todas las precauciones de
seguridad durante la instalación.