Draw-Tite 118559 T-ONE CONNECTOR - Manual

8. Secure the remainder of the T-Connector
harness with the cable ties provided, to prevent
damage or rattling and being careful to avoid
any areas that would pinch, cut or melt the wire.
9. Reinstall the plastic trim panels, threshold,
storage covers, floor covering and other items
that may have been removed during installation,
being careful not to pinch or cut the wires.
NOTE
Store 4-Flat in trunk area when not in use.
WARNING
Overloading circuit can cause fires. DO NOT
exceed lower of vehicle manufacturer rating or:
• Max. stop/turn light: 1 per side (2.1 amps)
• Max. tail lights: (5.6 amps)
Read vehicle’s owners manual & instruction
sheet for additional information.
ENGLISH
TOOLS REQUIRED:
Trim Panel Remover, 10mm Socket &
Ratchet or 10mm Wrench, Drill (3/32” Drill
Bit), 1/4” Socket, Wire Crimpers, Wire Cutters,
Philips Head Screwdriver, Test-probe
1. Open trunk and remove threshold panel.
Partially remove the corner felt trunk liner,
on both sides, exposing the vehicle’s taillight
wiring harness d.
2. Beginning on the driver’s side, separate the
vehicle’s wiring connectors, being careful not
to break the locking tabs. Insert the T-Connector
end, with the yellow wire, between the
vehicle wiring connectors and lock into place.
All connector surfaces should be clean and
free of dirt.
3. Route the T-Connector containing the
green wire below the threshold cover to the
passenger’s side taillight housing. Repeat step 2
for the passenger’s side using the T-Connector
containing the green wire.
4. Locate a suitable grounding point on the driver’s
side near the connectors. Drill a 3/32” hole
and secure white wire with eyelet using screw
provided. Do not drill into any exposed surfaces.
CAUTION
Verify what is behind any surface prior to
drilling to avoid damage to the vehicle and/
or personal injury. Do not drill into any
exposed surfaces.
5. Locate a flat surface in an out of the way place
and mount the T-Connector’s black box-module,
to prevent damage or rattling.
NOTE
This surface should be in an area that is
free of any moisture and mounted in an area
that it is high enough where it could not be
exposed to direct contact with any water
or liquid substance.
6. From inside the vehicle, connect the black 12 ga.
wire and the black wire from the T-Connector
black box with the supplied yellow butt
connector. Either route the black wire thru a
grommet and along the exterior frame or follow
the existing wiring along the thresholds into the
engine compartment up to the battery avoiding
areas that may pinch or break the wire e.
WARNING
If routing the wire thru a grommet and along
the exterior of the vehicle, be careful to avoid
any hot pipes, heat shields, the fuel tank or any
other points that may pinch or break the wire.
7. Disconnect the vehicle’s negative (-) battery
cable. If not removed, remove the fuse from
the yellow fuse holder (provided). After cutting
the fuse holder wire f, attach the ring terminal
and secure to the vehicle’s Positive (+) battery
cable g. Connect the other end of the fuse
holder to the black 12 ga. wire, using the
yellow butt connector (provided).
WARNING
Read and follow all warnings and cautions printed
on the tow vehicle’s battery. All connections must
be complete for the T-Connector to function
properly. Test and verify installation with a test
light or trailer once installed. For initial test, reset
vehicle electrical system by temporarily removing
the key from the ignition.
118559-037 Rev. A 5/30/2012
Installation Instructions
Directives de Montage
Instrucciones de Instalación
T-Connector
Connecteur en T
Conector en T
Hyundai Accent
d
e
f
g
READ THIS FIRST:
Read and follow all vehicle warnings and installation
instructions before beginning installation. Wear safety
glasses and use all safety precautions during installation.
LISEz CECI EN PREMIER:
Lire et observer toutes les consignes de sécurité et les
instructions avant de commencer l’installation. Durant
l’installation, veiller à toujours porter des lunettes de
protection et respecter les mesures de sécurité.
LEA ESTO PRIMERO:
Lea y siga todas las advertencias e instrucciones de
instalación del vehículo antes de empezar la instalación.
Use gafas de seguridad y todas las precauciones de
seguridad durante la instalación.