Draw-Tite 118510 T-ONE CONNECTOR - Manual

READ THIS FIRST:
Read and follow all vehicle warnings and
installation instructions before beginning installation.
Wear safety glasses and use all safety precautions
during installation.
LISEz CECI En PREmIER:
Lire et observer toutes les consignes de sécurité et les
instructions avant de commencer l’installation. Durant
l’installation, veiller à toujours porter des lunettes
de protection et respecter les mesures de sécurité.
LEA ESTO PRImERO:
Lea y siga todas las advertencias e instrucciones
de instalación del vehículo antes de empezar la
instalación. Use gafas de seguridad y todas las
precauciones de seguridad durante la instalación.
118510-037 Rev. A 08/25/2010
Installation Instructions
Directives de montage
Instrucciones de Instalación
T-Connector
Connecteur en T
Conector en T
Lexus HS250h
ENGLISH
TOOLS REQUIRED:
Trim Panel Remover, 10mm Socket &
Ratchet or 10mm Wrench, Drill (3/32” Drill Bit),
1/4” socket, Wire Crimpers, Wire Cutters,
Philips Head Screwdriver, Test-probe
1. Open trunk/hatch to locate the vehicle wiring
inside the vehicle’s rear cargo area by partially
removing the plastic threshold cover, side
access panels or carpet panels and cargo
trays d, e, f.
2. On the driver and passenger sides of the
vehicle, locate the vehicle’s taillight wiring
harness g. The taillight wiring harness will
have a connection point, on both sides,
matching the ends of the T-Connector. Separate
this connector, being careful not to break the
locking tabs. All connector surfaces should be
clean and free of dirt.
3. On the passenger side, insert the T-Connector
end with the green wire between the vehicle
wiring connectors and lock into place.
Route the T-Connector end with the yellow wire
to the driver’s side behind the panels and along
the threshold.
Repeat step 3 for T-Connector end with the
yellow wire.
4. On the passenger side, locate a suitable
grounding point near the connector.
OPTIOn 1:
Clean dirt and rustproofing from the area.
Drill a 3/32” hole and secure the white wire
using the eyelet and screw provided. (Do not
drill into vehicle floor or bed. Do not drill into
any exposed surfaces.)
OPTIOn 2:
Locate existing ground stud. Loosen bolt,
place screw eyelet on stud and re-tighten bolt.
CAUTIOn
Verify what is behind any surface prior to drilling
to avoid damage to the vehicle and/or personal
injury. Do not drill into any exposed surfaces.
5. Use only with 12V Battery Systems.
WARnInG
Read and follow all warnings and cautions
printed on the tow vehicle’s battery.
WARnInG
Locate the battery inside the vehicle’s trunk.
It will be located inside a compartment on
the passenger’s side behind the rear seat
h, i. Disconnect and isolate the vehicle’s
Negative (-) battery terminal.
6. Attach the fuse holder (with fuse removed)
to the positive (+) terminal of the battery.
Reconnect the vehicle’s Negative (-) battery
cable and install the 10 amp fuse into the
fuse holder from step 5.
See tow vehicle’s owners manual for any
special battery reconnection instructions.
WARnInG
All connections must be complete for the
T-Connector to function properly. Test and
verify installation with a test light or trailer once
installed. For initial test, reset vehicle electrical
system by temporarily removing the key from
the ignition.
7. On the passenger’s side, mount the T-Connector
black box using the double-sided tape provided.
Secure the remainder of the T-Connector
harness with the cable ties provided, to prevent
damage or rattling and being careful to avoid
any areas that would cut or pinch the wire.
8. Reinstall the plastic trim panels, threshold,
storage covers, floor covering and other items
removed during installation, being careful not
to pinch or cut the wires.
nOTE
Store 4-Flat connector in spare tire compartment
when not in use.
WARnInG
Overloading circuit can cause fires. DO NOT
exceed lower of towing manufacturer rating or:
• Max. stop/turn light: 1 per side (2.1 amps)
• Max. tail lights: (5.6 amps)
Read vehicle’s owners manual & instruction
sheet for additional information.
d g
e
f i
h