Draw-Tite 118594 T-ONE CONNECTOR - Manual

ENGLISH
TOOLS REQUIRED:
Trim Panel Remover, Drill (3/32” Drill Bit),
Philips Head Screwdriver, Test-probe
1. Open trunk. Temporarily remove the rear
threshold plate. Partially remove the felt
trunk liner behind the taillights def.
2. On the driver and passenger sides of the
vehicle, locate the vehicle’s taillight wiring
harness. The taillight wiring harness will have
a connection point, on both sides, matching
the ends of the T-Connector. Separate this
connector, being careful not to break the
locking tabs. All connector surfaces should
be clean and free of dirt g.
3. On the driver’s side, insert the T-Connector end,
with the yellow wire, between the vehicle wiring
connectors and lock into place. Be careful not
to damage the locking tabs and be sure that
connectors are fully inserted with locking tabs
in place.
4. Route the T-Connector end with green wire to
the passenger ‘s side behind the panels and
along the threshold. Repeat step 3 using the
T-Connector ends containing the green wire.
5. Locate a suitable grounding point near the
connector. Clean dirt and rustproofing from
the area. Drill a 3/32” hole and secure the white
wire using the eyelet and screw provided.
CAUTION
Verify what is behind any surface prior to drilling
to avoid damage to the vehicle and/or personal
injury. Do not drill into any exposed surfaces.
6. From inside the vehicle, connect the black 12
ga. wire and the red wire from the T-Connector
black box with the supplied yellow butt
connector. Either route the black wire thru a
grommet and along the exterior frame or follow
the existing wiring along the thresholds into the
engine compartment up to the battery avoiding
areas that may pinch or break the wire h.
WARNING
If routing the wire thru a grommet and along
the exterior of the vehicle, be careful to avoid
any hot pipes, heat shields, the fuel tank or any
other points that may pinch or break the wire.
7. Disconnect the vehicle’s Negative (-) battery
cable. If not removed, remove the fuse from the
yellow fuse holder (provided). After cutting the
fuse holder wire, attach the ring terminal and
secure to the vehicle’s Positive (+) battery cable
i. Connect the other end of the fuse holder
to the black 12 ga. wire, using the yellow butt
connector (provided) j.
WARNING
Read and follow all warnings and cautions
printed on the tow vehicle’s battery.
8. Reconnect the vehicle’s Negative (-) battery
cable and install the 10 amp fuse into the
fuse holder from step 7.
WARNING
All connections must be complete for the
T-Connector to function properly. Test and
verify installation with a test light or trailer once
installed. For initial test, reset vehicle electrical
system by temporarily removing the key from
the ignition.
9. Locate a flat surface in an out of the way place
and mount the T-Connector’s black box-module,
to prevent damage or rattling.
10. Secure the remainder of the T-Connector
harness with the cable ties provided, to prevent
damage or rattling and being careful to avoid
any areas that would pinch, cut or melt the wire.
11. Replace carpet, and any other clips or panels
that were removed during installation being
careful not to cut or pinch the wires.
NOTE
Store 4-Flat in trunk area when not in use.
WARNING
“Overloading circuit can cause fires. DO NOT
exceed lower of towing manufacturer rating or:
• Max. stop/turn light: 1 per side (2.1 amps)
• Max. tail lights: (5.6 amps)
Read vehicle’s owners manual & instruction
sheet for additional information.
READ THIS FIRST:
Read and follow all vehicle warnings and installation
instructions before beginning installation. Wear safety
glasses and use all safety precautions during installation.
LISEz CECI EN PREmIER:
Lire et observer toutes les consignes de sécurité et
les instructions avant de commencer l’installation.
Durant l’installation, veiller à toujours porter des lunettes
de protection et respecter les mesures de sécurité.
LEA ESTO PRImERO:
Lea y siga todas las advertencias e instrucciones de
instalación del vehículo antes de empezar la instalación.
Use gafas de seguridad y todas las precauciones de
seguridad durante la instalación.
118594-037 Rev. A 4/24/2013
Installation Instructions
Directives de montage
Instrucciones de Instalación
T-Connector
Connecteur en T
Conector en T
Kia Forte
h
i
j
d
e
f g