Draw-Tite 118608 T-ONE CONNECTOR - Manual

9. Reconnect the vehicle’s Negative (-) battery
cable and install the 10 amp fuse into the
fuse holder from step 8.
WARNING
All connections must be complete for the
T-One ® T-Connector to function properly.
Test and verify installation with a test light
or trailer once installed. For initial test, reset
vehicle electrical system by temporarily
removing the key from the ignition.
10. On driver’s side, locate a flat surface in an
out of the way place and mount the T-One ®
T-Connector’s black convertor box with the
double sided tape. Secure the remainder of
the T-One ® T-Connector harness with the cable
ties provided, to prevent damage or rattling
and being careful to avoid any areas that would
pinch, cut or melt the wire.
11. Reinstall the plastic trim panels, threshold,
storage covers, floor covering and other items
removed during installation, being careful not
to pinch or cut the wires.
NOTE
Store 4-Flat in rear cargo area when not in use.
WARNING
Overloading circuit can cause fires. DO NOT
exceed lower of towing manufacturer rating or:
• Max. stop/turn light: 1 per side (2.1 amps)
• Max. tail lights: (5.6 amps)
Read vehicle’s owners manual & instruction sheet
for additional information.
ENGLISH
TOOLS REQUIRED:
Trim Panel Remover, Drill (3/32” Drill Bit),
Philips Head Screwdriver, Test-probe
1. Open rear hatch. Temporarily remove the
rear threshold plate, storage covers and
floor covering de .
2. Partially remove the rear interior trim panels on
both the driver and passenger side of the vehicle.
Several trim panel fasteners will need to be
removed to remove the panels. Set aside all items
removed being careful not to damage parts f .
3. On the driver and passenger sides of the
vehicle, locate the vehicle’s taillight wiring
harness. The taillight wiring harness will have
a connection point, on both sides, matching the
ends of the T-One ® T-Connector. Separate this
connector, being careful not to break the locking
tabs. All connector surfaces should be clean
and free of dirt g .
4. On the driver’s side, insert the T-One ®
T-Connector end, with the yellow wire,
between the vehicle wiring connectors and
lock into place. Be careful not to damage the
locking tabs and be sure that connectors are
fully inserted with locking tabs in place.
5. Route the T-One ® T-Connector end with green
wire to the passenger ‘s side behind the panels
and along the threshold. Repeat step 4 for
T-One ® T-Connector end with the green wire.
6. Locate a suitable grounding point near the
connector such as the vehicle’s frame or cross
member. (Do not drill into vehicle floor or bed.)
Clean dirt and rustproofing from area. Drill a
3/32” hole and secure white wire using eyelet
and screw provided.
CAUTION
Verify what is behind any surface prior to drilling
to avoid damage to the vehicle and/or personal
injury. Do not drill into any exposed surfaces.
7. From inside the vehicle, connect the black
12 ga. wire and the red wire from the T-One ®
T-Connector black box with the supplied yellow
butt connector. Either route the black wire thru
a grommet and along the exterior frame or follow
the existing wiring along the thresholds into the
engine compartment up to the battery avoiding
areas that may pinch or break the wire h .
WARNING
If routing the wire thru a grommet and along
the exterior of the vehicle, be careful to avoid
any hot pipes, heat shields, the fuel tank or any
other points that may pinch or break the wire.
8. Disconnect the vehicle’s Negative (-) battery
cable. If not removed, remove the fuse from
the yellow fuse holder (provided). After cutting
the fuse holder wire i , attach the ring terminal
and secure to the vehicle’s Positive (+) battery
cable. Connect the other end of the fuse holder
to the black 12 ga. wire, using the yellow butt
connector (provided) j .
WARNING
Read and follow all warnings and cautions printed
on the tow vehicle’s battery.
Installation Instructions
Directives de Montage
Instrucciones de Instalación
T-One ® T-Connector
T-One ® Connecteur en T
T-One ® Conector en T
Scion xD
118608-037 Rev. A 10/8/2013
READ THIS FIRST:
Read and follow all vehicle warnings and installation
instructions before beginning installation. Wear safety
glasses and use all safety precautions during installation.
LISEz CECI EN PREMIER:
Lire et observer toutes les consignes de sécurité et les
instructions avant de commencer l’installation. Durant
l’installation, veiller à toujours porter des lunettes de
protection et respecter les mesures de sécurité.
LEA ESTO PRIMERO:
Lea y siga todas las advertencias e instrucciones de
instalación del vehículo antes de empezar la instalación.
Use gafas de seguridad y todas las precauciones de
seguridad durante la instalación.
PAGE 1 OF 3
d
e f
h
i
g
j