Audi AUD-S - Manual (Page 10)

TO AVOID DAMAGE TO DOOR AND OPERATOR
ENSURE ALL DOOR LOCKS ARE DISABLED.
USE AN INTERLOCK SWITCH IF A LOCK IS
REQUIRED TO RETAIN FUNCTIONALITY.
CAUTION
TO PREVENT THE RISK OF PERSONAL
INJURY AND/OR DAMAGE TO DOOR OR
PROPERTY, ONLY OPERATE DOOR
CONTROL WHEN DOOR IS IN CLEAR VIEW.
IF CONTROL STATION CANNOT BE
LOCATED WHERE THE DOOR IS VISIBLE
OR IF ANY OTHER DEVICE IS USED TO
CONTROL THE DOOR AN AUXILIARY
ENTRAPMENT DEVISE (DOOR EDGE OR
PHOTOELECTRIC) MUST BE CONNECTED.
WARNING
RISK OF ENTRAPMENT THAT MAY
RESULT IN SERIOUS PERSONAL INJURY
OR DEATH. DISCONNECT POWER TO
THE OPENER BEFORE AND DURING
INSTALLATION OF AN ACCESSORY
REVERSING DOOR EDGE OR
PHOTOELECTRIC DEVICE. DO NOT
RECONNECT POWER TO OPENER UNTIL
INSTRUCTED TO DO SO. ENSURE
DOORWAY IS CLEAR BEFORE STARTING
TESTING OF UNIT.
WARNING
TO PREVENT THE RISK OF PERSONAL INJURY
OR DEATH :
• DISCONNECT POWER AT THE FUSE BOX
BEFORE PROCEEDING.
• ELECTRICAL CONNECTIONS MUST BE MADE
BY A QUALIFIED INDIVIDUAL.
• OBSERVE LOCAL ELECTRICAL CODES WHEN
WIRING THE OPERATOR.
WARNING
WARNING: The AUD-S Series operators have been designed
and constructed for use with voltages from 115 Volts AC to
480 Volts AC, in single or three phase. Check the operator
nameplate label on the control box cover for the proper
voltage and phase. The application of an improper input
voltage or phase will result in catastrophic failure to the
internal electrical components.
Observe local electrical codes when wiring the operator.
When hard wiring, observe state and local electrical codes. A
wiring diagram is attached to the inside of the control box cover.
Connect the appropriate voltage and phase power leads to the
appropriate terminals as per the wiring diagram and connect a
ground wire to the grounding screw. On three phase units,
incorrect phasing of the power supply will cause the motor to
rotate in the wrong direction (open when CLOSE button is pushed
and vice versa). To correct this, interchange any two of the
incoming three phase conductors.
The wiring diagram attached inside the cover of the control box
details all of the field wiring terminal connections for the operator.
Always connect the wires to the push-button controls and auxiliary
devices exactly as shown.
Warning: Control voltage of the opener is 5 volts DC, Class 2.
Do not run the power leads and control circuit wiring in the same
electrical conduit.
Note: AUD-S Series model openers are pre-wired for door
reversing edge components. To comply with code requirements,
the door reversing edge components must be installed and wired
to the opener. Refer to Figure 15 Door Edge component
installation and Figure 16 for Door Edge and photoelectric
device wiring.
If a Safe-Finish™ or Access Alliance Safe-Finish II™ photo-
beam is connected and the photo-beam detects an obstruction or
becomes inactive, an opening door continues to open and a
closing door stops, pauses and starts open. While in this mode,
if a problem is detected while the opener is stopped, a close
action will require constant activation of the push button. If the
photo-beam is attached and is properly working for 1 second, it
will be auto detected and the monitored function will be
turned on. Once the monitoring function is active, it will remain
active even if the power is removed and the photo-beam is
disconnected and power is restored. While in this mode, if a
problem is detected while the opener is stopped, a close will
require constant activation.
Openers which are equipped with a reversing edge circuit may
have one or more additional means of control which should be
wired in accordance with the diagram supplied in the opener
and also illustrated on Pages 20 & 21. To add a second three
button station, refer to Figure 18.
Number 22 gauge wire or heavier must be used for wiring
the control stations and auxiliary control devices to the
operator. Smaller gauge wire will cause operational
problems, especially when multiple push-button stations are
used or during summer months.
10
ELECTRICAL WIRING INSTRUCTIONS