Aphex Systems Compellor 320D - Manual (Page 2)

DRIVE METER SELECT
PROCESS
INPUT
OUT IN
OUTPUT
UNLINK
LEVELING &
COMPRESSION
STEREO
ENHANCE LEVELING
LINK
G.R. DVG
S
0dB
F
RATE
OUT IN
LIMITER
PROCESS BALANCE OUTPUT THRESHOLD
SILENCE GATE 2
-15
4
-12
6
-9
8
-6
10
-3
12
0
14
+3
16
+6
18
+9
20
+12
GR(dB)
PGM(dB)
- COMPRESS LEVEL +10dB -10dB 0dB -40dB
DRIVE
PROCESS
OUT IN
DVG
S
0dB
F
RATE
OUT IN
LIMITER
PROCESS BALANCE OUTPUT THRESHOLD
SILENCE GATE
COMPELLOR ®
MODEL 320D
ANALOG & DIGITAL I/O
POWER 2
-15
4
-12
6
-9
8
-6
10
-3
12
0
14
+3
16
+6
18
+9
20
+12
GR(dB)
PGM(dB)
- COMPRESS LEVEL +10dB -10dB 0dB -40dB
AC LINE 30 WATTS
FUSE: 100-120V (3/8ASB) 200-240V (1/4ASB)
PROTECTED BY ONE OR MORE OF
THE FOLLOWING PATENTS:
4155047 4578648 5422602
COMPELLOR ®
MODEL 320D
S Y S T E M S
|
COMMERCIAL
AUDIO
EQUIPMENT
59887
ANALOG CH2 DIGITAL AES3 INPUT
AUDIO
SOURCE
SELECT
ANALOG CH1
IN 32-96kHz OUT IN
OP
LEVEL
-10 +4
OUT IN OUT
ANALOG
DIGITAL
OP
LEVEL
-10 +4
MADE
IN
U.S.A.
SPECIFICATIONS
5.1A ANALOG INPUTS
Connector:
3 pin XLR female
Type: transformerless, servo balanced, RFI fIltered
Impedance: 22K-ohms balanced, 11K-ohms unbalanced
Operating Level: user selectable +4dBu or -10dBV
Max input level: +27dBu(ref = +8), +25dBu(ref = +4), +10.8dBV(ref = -10)
CMRR: >90dB/100Hz, >70dB, 1KHz, >50dB, 20KHz
5.1B DIGITAL INPUT
Connector:
3 pin XLR female
Type: transformer balamced
Impedance: 110 ohms
5.2A ANALOG OUTPUTS
Connector:
3 pin XLR male
Type: electronic servo balanced (unbalanced without 6dB loss)
Impedance: 65 ohms bal or unbal (nominal load 600 ohms or greater)
Max level out (bal): +25dBu(ref = +4), +10.8dBV(ref = -10)
Max level out (unbal): +20dBu(ref = +4), +10.8dBV(ref = -10)
5.2B DIGITAL OUTPUTS
Connector:
3 pin XLR male
Type: transformer balanced
Impedance: 110 ohms
5.3 AUDIO
Frequency response:
+/- 1dB 10Hz to 65KHz
Hum & noise: measured for a 1KHz tone at unity gain
No gain reduction: -67dBu(ref = +4), -86dBV(ref = -10)
10dB gain reduction: -74dBu(ref = +4), -89dBV(ref = -10)
Crosstalk @ 20KHz: -65dBu(ref = +4), -78dBV(ref = -10)
Dynamic THD typically .05% for 1KHz at 20dB gain reduction
Static THD: .025% at maximum output level
IMD, max output: .13%(ref = +4), .4%(ref = -10)
5.4 SYSTEM FUNCTIONS
Compression
Frequency Discriminate Leveling
Peak Limiter
Dynamic Verification Gate (DVG)
Dynamic Recovery Computer (DRC)
Silence Gate
Stereo Enhance
5.5 THRESHOLD
Compressor:
30dB below nominal level
Leveler: 30dB below nominal level
Limiter: 14dB above nominal level
5.6 RATIO
Compressor:
1.1:1 to 3:1 program dependent
Leveler: 20:1
Limiter: >30:1
5.7 ATTACK TIMES
Compressor:
5 to 50mSec program dependent
Leveler, fast: 20Hz = 1.5 Sec > 1KHz Frequency Discriminate Leveler
Leveler, slow: 20Hz = 5 Sec > 1KHz Frequency Discriminate Leveler
Limiter: 1 uSec
5.8 RELEASE TIMES
Compressor:
200 mSec to 1 Sec program dependent
Leveler, fast: 3 Sec
Leveler, slow: 10 Sec
Limiter: 200 mSec
5.9 DIGITAL AUDIO
Input SR:
Locks to 44.1, 48, 88.2, 96kHz +/- 3%
I/O Type: AES/EBU 110 ohms XLR
Default Output SR: User definable by replacing crystal; 48kHz standard
Word Clock: Not Supported
5.10 OTHER SPECIFICATIONS
AC input:
IEC standard receptacle with voltage selector, fuse, & filter
Power requirements: 100-120-220-240VAC, 50-60Hz
Power input (max): 20 watts
Dimensions: 19”W x 1.75” H x 10.125” overall depth
depth behind front panel = 9.25”
Net weight: 8 lbs.
Shipping weight: 9 lbs.
320D Compellor
Get the Best of Both Worlds
DUAL MONO or STEREO
The 320D converts between acting as two independent mono processors and
one linked stereo processor by front panel selection. This is true with both analog
and digital I/O.
ANALOG or DIGITAL IN, ANALOG and DIGITAL OUT!
The 320D serves as a fine A to D converter with processing. When you use the
analog input, the digital output contains the Compellor’s processing and is there-
fore ready for use in almost any application. Conversely, the 320D serves as a fine
D to A converter. When you use the digital input, the analog output contains the
Compellor’s processing, and is properly leveled and packaged.
ANALOG and DIGITAL AUDIO INTERFACES
The professional analog audio inputs and outputs are fully balanced and adapt
to consumer or professional operating levels at the touch of a button. Analog or
digital source selection is made at the rear panel.
For digital interfacing, the 320D contains a high quality 24-bit low noise codec
to receive digital audio and to transmit digital audio. Once the incoming digital
audio is converted by the DAC section, it passes through the Compellor as normal
audio. The audio output is then converted back into digital by the ADC section of
the codec.
The rear panel AES3 jacks are standard professional XLR 110 ohm interfaces.
There is no word clock input or output. Synchronizing is accomplished from the
AES3 input signal or an internal clock. When a digital input is present, the output is
synchronized to the input sample rate. If no digital input is present, the digital out-
put automatically locks to the internal default sample clock. The user can specify
the default sample rate by changing the internal crystal. Spare crystals for 32kHz,
44.1kHz, 48kHz, and 96kHz are supplied with the unit free of charge.
The Model 320D codec translates the -20dBFS level of the digital audio source to
the 0dB reference within the Compellor circuits. The average output levels will tar-
get around -20dBFS. The selectable peak limiter’s threshold translates to -6dBFS.
Thus, no digital audio output peaks will rise above -6dBFS when the limiter is on.
The combination of averaging the level around -20dBFS and holding peaks below
-6dBFS packages the audio perfectly for natural sound quality and for most trans-
fer or transmission purposes. For example, the digital audio would be ready for
direct input to an MP3 coder, HD recorder, broadcast digital STL, .wav file, etc.
ARCHITECT’S SPECIFICATIONS
A single rack space electronic audio level controlling device with both analog and
AES3 digital audio I/O combining leveling, compression, and limiting for automati-
cally and continuously correcting audio levels. The level controller shall be of such
design as to reduce the audible artifacts of compression. It shall also be of such
design as to prevent the rising of background noises when the audio source stops
producing sound. The leveling function shall adapt discriminately to frequencies
in a manner to reduce the impression of bass sounds losing impact in music. The
compression function shall contain a means to adapt itself to the peak factor of
sound so as to improve the consistency of volume levels. The limiter shall operate
at a threshold 14dB above the 0VU reference level. Digital and analog audio out-
puts shall be simultaneously available. The input shall be switchable between the
analog and digital sources. The AES3 I/O shall operate normally at sample rates
from 32kHz to 96kHz.