Hudson Valley Lighting HANOVER 141 - Manual

140 & 41 INSTALLATION INSTRUCTIONS
GENERAL
1. To insure the success of this fixture installation, the following instructions and diagram(s) should be read and understood.
All electrical connections must be made in accordance with the National Electric Code and local codes and ordinances.
If you are uncertain of the methods of installing electrical wiring and lighting fixtures, secure the services of a qualified licensed electrician.
2. TOOLS NEEDED: Blade screwdriver, small adjustable wrench or slip-joint pliers, electrical current tester, stepladder and electrical tape.
NOTE: The important safeguards and instructions outlined on this sheet cannot cover all possible conditions and situations that may occur.
It must be understood that common sense, caution and care are factors that cannot be built into any product.
Caution and care must be supplied by the person(s) installing, operating and caring for this lighting fixture.
INSTALLATION PREPARATION
1. TURN OFF THE ENTIRE ELECTRICAL CIRCUIT TO WHICH THE LIGHTING FIXTURE IS TO BE ATTACHED.
Move the appropriate circuit breaker to the "off" position or completely remove the fuse controlling the circuit.
2. If an existing fixture is being replaced, remove it and note to which of the wires in the outlet box the fixture was attached.
DO NOT SEPARATE ANY OTHER WIRES THAT MAY BE IN THE BOX. DO NOT DAMAGE THE INSULATION OF OLDER WIRING.
In regular circumstances the BLACK wire will be the "Hot" lead and the WHITE wire will be the "Neutral" or "Common" lead.
A GREEN or BARE COPPER wire is the "Ground". In older buildings it is always good practice to reconfirm the polarity of the wiring.
3. This fixture is designed to be mounted on a correctly installed standard round or octagon box or a through wiring box with a plaster frame.
The box must be securely mounted to the structure of the building. The crossbar and hardware supplied should be used.
Directly mounting the fixture to the outlet box may make it impossible to correctly align the fixture.
FIXTURE INSTALLATION
1. Remove the fixture, parts and parts bag(s) from the carton. Before discarding the carton, double check to make certain that all parts are found.
2. (Starting at the back), thread the 2 longest screws into the crossbar. (The green screw is in the front).
Attach the crossbar to the outlet box. (The green screw should face the floor).
3. Thread the small hex nuts onto the screws. Adjust the screws so that they extend 3/16" beyond the canopy of the fixture,
Lock the hex nuts against the mounting ring.
4. Fasten the bare ground wire to the green or bare copper wire in the outlet box or to the green screw on the crossbar.
NEVER FASTEN THE GROUND WIRE TO THE BLACK OR "HOT" WIRE !
FAILURE TO FOLLOW THIS INSTRUCTION COULD RESULT IN SERIOUS INJURY OR DEATH !
5. Fasten the white fixture lead to the white wire in the outlet box.
Fasten the wires together with an approved fastener (wire nut).
Starting about 1' below the fastener, tightly wrap the connection
with electrical tape so that the connection seals the end of the fastener.
Make sure that there is no exposed wire or strands
that could cause a dangerous short circuit !
6. Connect the black fixture lead to the black wire in the outlet box.
Fasten the joined wires as in step 5.
7. Using the end balls, fasten the fixture to the outlet box.
8. Hook the chains onto the canopy and the fixture ring onto the chains.
9. Screw the lower stem into the junction body.
10. Install the lamps ( light bulbs).
NOTE: This fixture is rated for 60 watt type B, BA, C or CA lamps.
DO NOT EXCEED RECOMMENDED WATTAGE !
11. Place the glass over the stem and into the ring.
12. Thread the glass support and coupling onto the stem to hold the glass in place.
DO NOT OVERTIGHTEN !
13. Screw the extension nipple into the coupling.
14. Place the lower cup onto the extension nipple and install the finial.
16. Restore power to circuit at breaker or fuse box.
092805
electrical tape
Approved fastener
(wire nut)
Outlet box
Green screw
Crossbar
Lower cup
End ball
Finial
Glass
Hex nut
Screw
Canopy
Lamp
Chain
Fixture ring
Stem
Junction body
Glass support
Coupling
Extension nipple