Hudson Valley Lighting MIDDLEBURY 932 User Manual
Hudson Valley Lighting Lighting
931 & 932
Electrical tape
Approved fastener
(Wire nut)
Hudson Valley Lighting, Inc.
P.O. Box 7459
106 Pierces Road
Newburgh, NY 12550
(800) 814-3993
GENERAL
1. To ensure the success of the fixture installation, the following instructions
and diagram(s) should be read and understood.
2. All electrical connections must be made in accordance with the National
Electric code and local codes and ordinances. If you are uncertain of the
methods of installing electrical wiring and lighting fixtures secure the services
of a qualified licensed electrician.
3. TOOLS NEEDED: Blade screwdriver, phillips screwdriver, slip joint pliers
or small adjustable wrench, wire cutter/stripper, electrical current tester,
stepladder and electrical tape. NOTE: The important safeguards and
instructions outlined on this sheet are not meant to cover all possible
conditions and situations that may occur. It must be understood that common
sense, caution and care are factors that cannot be built into any product.
Caution and care must be supplied by the person(s) installing, operating and
maintaining this lighting fixture.
INSTALLATION PREPARATION
1. TURN OFF THE ENTIRE ELECTRICAL CIRCUIT TO WHICH THE
LIGHTING FIXTURE IS TO BE ATTACHED.
Move the appropriate circuit
breaker to the “off position or completely remove the fuse controlling the circuit.
2. If an existing fixture is being replaced, remove it and note to which of the
wires in the outlet box the fixture was attached.
DO NOT SEPARATE ANY
OTHER WIRES THAT MAY BE IN THE BOX. DO NOT DAMAGE THE
INSULATION OF OLDER WIRING.
In regular circumstances the BLACK
wire will be the “Hot” lead and the WHITE wire will be the “Neutral” or
“Common” lead. A GREEN or BARE COPPER wire is the “Ground”. In older
buildings it is always good practice to reconfirm the polarity of the wiring.
3. This fixture is designed to be mounted on a standard round or octagon box.
The box must be securely mounted to the structure of the building.
FIXTURE INSTALLATION
1. Remove the fixture, shades and parts bag(s) from the carton. Before
discarding the carton, double check packing to make certain that all parts are
found.
2. (Starting at the back), thread the 2 longest mounting screws into the
Mounting bar, (The green screw is in the front). Attach the mounting bar
To the outlet box. (The green screw should face the floor).
3. Thread the small hex nuts onto the mounting screws. Adjust the mounting
Screws
so that they extend 3 1/16” beyond the inside surface of the
fixture, lock the hex nuts against the crossbar.
4. Fasten the green fixture wire to the green or bare copper wire in the box
or fasten it to the mounting plate with green screw provided.
NEVER FASTEN THE GROUND WIRE TO THE BLACK OR “HOT” WIRE!
FAILURE TO FOLLOW THIS INSTRUCTION COULD RESULT IN
SERIOUS INJURY OR DEATH!
5. Fasten the white fixture wire to the white wire in the outlet box. Fasten
the wires to together with an approved fastener (wire nut). Starting about
1” below the fastener, tightly wrap connection with electrical tape so
that the tape seals the end of the fastener. Make sure that there is no
exposed wire or strands that could cause a dangerous short circuit !
6. Connect the black fixture wires to the black wire in the outlet box.
Fasten the joined wires as in step 5.
7. Using the end ball to fasten the fixture to the outlet box.
8. Install the lamps (light bulbs).
NOTE: This fixture is rated for 60 watt Type B lamps.
DO NOT EXCEED RECOMMENDED WATTAGE !
9. Carefully place the glass panel into the frame and put four pieces of metal
diffusers covered square frame’s each corner then install the frame back to
the ceiling pan by twist lock key slot.
10. Restore power to circuit at breaker or fuse box.
Mounting bar
Green screw
Screw
Outlet box
Ceiling pan
Mounting screw
Key slot
Metal diffuser
End ball
Lamp
Frame
Glass panel