INSTEON In-LineLinc Dimmer (2475D) Quick Start User Manual
Quick start guide, Fanlinc™ insteon
2475F Rev. 7/5/2012 11:40 AM / See Owner’s Manual for Warranty Information, Patented
© Copyright 2012, INSTEON, 16542 Millikan Ave., Irvine, CA 92606, 800-762-7845
Fan (red)
Lights (blue)
Fan
LED
Set Button
(fan)
Set Button
(lights)
Light
LED
Neutral
(white)
Line
(black)
Installation
1) Using your fan pull chains, turn light on and set fan to highest speed.
Note: All fan and light controls will be conducted through FanLinc
once installed.
2) Turn off the breaker (remove fuse) supplying power to the fan’s box.
3) Identify Line, Neutral and Load lines for light and fan separately.
4) Remove the ceiling fan from the electrical box.
5) Disconnect the wires from the ceiling fan and light (if applicable).
6) Connect FanLinc white wire and the fixture Neutral wire to the house
Neutral with a wire nut.
7) Connect FanLinc blue wire to the fixture’s light wire (if fixture does
not have a light, cap the blue wire).
8) Connect FanLinc red wire to the fixture fan wire with a wire nut.
9) Connect FanLinc black wire to Line with a wire nut.
10) Ensure all connections are secure with no exposed copper.
11) Turn breaker back on.
FanLinc Light LED will turn
green
.
FanLinc Fan LED will turn
red
.
IMPORTANT: If you don’t have home control software (HouseLinc)
or a SmartLinc Hub, program all manual links now before
reinstalling fan.
Program Fan as an INSTEON Responder
1) Referencing the table below, tap FanLinc Fan Set button until
beeper and Fan LED indicate the desired fan speed. (For safety, fan
will not spin when Fan Set button is tapped.)
1st
Low
Single beep
Blinks
green
slow
2nd
Medium
Double-beep
Blinks
green
medium
3rd
High
Fast double-beep
Blinks
green
fast
4th
Off
None
Red
2) Press and hold the scene controller Set button until it beeps.
1
Controller LED will start blinking.
3) Press and hold FanLinc Fan Set button until FanLinc double-beeps.
Controller will double-beep
and its LED will stop blinking.
4) Temporarily hang fan from the mounting ring so the fan can spin
safely. While clear of fan blades confirm the scene addition was
successful by pressing On/Off on your controller.
FanLinc Fan LED will toggle between
green
and
red
.
5) To program fan from another controller, turn fan off, remove from
mounting ring and repeat steps 1-4.
Program Light as an INSTEON Responder
1) Press and hold controller button until it beeps.
Controller LED will start blinking.
2) Tap FanLinc Light Set button until the ceiling fan light is on.
FanLinc Light LED will turn
green
.
3) Press and hold FanLinc Light Set button until FanLinc double-beeps.
FanLinc Light LED will flash once.
Controller will double-beep
and its LED will stop blinking.
4) Test by tapping On/Off on controller.
Ceiling fan light will toggle between on and off.
5) To program light from another controller, repeat steps 1-4.
1
Most models
2
If the controller does not have a beeper, wait until its LED begins blinking.
3
Most models
Reinstall Fan
1) Carefully remount cowling with FanLinc inside (or in electrical box).
2) Align cable tie with the notches of the FanLinc case, ensuring that cable tie
and wires will not interfere with any moving parts. Secure to fan bracket.
Support
Owner’s Manual and current Quick Start Guide:
Call: INSTEON Support Line at 800-762-7845
This device complies with FCC Rules and Industry Canada license-exempt RSS standard(s). Operation
is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this
device must accept any interference, including interference that may cause undesired operation of the
device.
Le present appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts
de licence. L'exploitation est autorise aux deux conditions suivantes: (1) l'appareil ne doit pas produire
de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le
brouillage est susceptible d'en compromettre le fonctionnement.
Quick Start Guide
FanLinc™ INSTEON
®
Ceiling Fan and Light
Remote Controller (Dual-Band)
Model: 2475F
FOR CEILING FANS ONLY
What's Included
•
FanLinc • Four (4) wire nuts • One (1) cable tie