KT&C KPC-Xi210HD - Manual (Page 2)

How to connect video and audio
1. Optionally connect a microphone or line in mono signal to the Line in/MIC connector.
2.Optionally connect a speaker to Line out connector.
3. Optionally insert a Micro SD card to Micro SD socket.
4. Connect the camera to the network using a UTP cable (CAT.5), Power can be supplied via the
network cable (PoE)
5. Connect DC 12V or AC 24V to the power terminal. This is not necessary if the Network Camera is
connected to PoE hub or midspan. Caution: Do not apply DC 12V and AC 24V at the same time.
CAUTION : Do not apply DC 12V and AC 24V at the same time.
6. Check that the indicator LEDs indicates the correct conditions.
7. Connect the analog monitor to the service video connector for adjusting focus and press and quickly
release the reset switch for focus assistant mode. Then you can select normal view or focus view
mode using the reset switch.
CAUTION : When you use focus assistant mode, “Focus View” mode is recommended
for more exact focus.
CAUTION : Focus assistant mode will be automatically exited after 3 minutes
for normal operation.
5. Assign an IP address
To make it accessible on the network, the Network Camera must be assigned an IP address.
Note:
• A network DHCP server is optional.
• The Network Camera has the default IP address 192.168.0.123.
• If IP assignment fails, check that there is no firewall blocking its operation and check that the Network
Camera and your computer's IP is located on the same subnet.
Assign an IP address using IP Installer
IP installer automatically search and display KT&C network devices on your
network. The application can also be used to manually assign a static IP address.
Note:
The computer running the IP installer must be on the same network segment (physical subnet) as the Network
Camera.
1. Check that the Network Camera is connected to the network and that power has been applied.
2. Start KT&C IP installer.
3. When the Network Camera appears in the window, select the Network Camera which needs to
assign the IP address.
A. Refresh Device List – Rescan local network to find the Network Camera.
B. Authenticate – Enter the administrator ID and password.
C. Host Name – Enter the Host Name of the Network Camera.
D. IP Settings
i. Dynamic – Assign dynamic IP address automatically from DHCP server on your network.
ii. Static – Assign static IP address manually.
iii. Port – Enter the HTTP port the Network Camera will use. The default setting is 80.
Alternatively, any port in the range 1024-65535 may be used, but check first with your
system administrator before changing the default setting.
E. Network Settings
i. Subnet Mask – Specify the mask for the subnet the Network Camera located on.
ii. Gateway – Specify the IP address of the default router (gateway) used for connecting devices
attached to different networks and network segments.
iii. Pri. DNS – Enter the IP address of the primary DNS server. This server provides the
translation of host names to IP addresses on your network.
iv. Sec. DNS – Specify the IP address of the secondary DNS server. This will be used if the
primary DNS server is unavailable.
4. Click “Set” button to save configuration.
Accessing the Network Camera
1. Start your browser.
2. Enter the IP address or host name of the Network Camera in the Address field of your brows
3. If you are accessing the Network Camera for the first time, you will see the following warning
message as shown below.
4. Click the warning message and select “Install ActiveX Control…”.
5. Click “Install” to install the KT&C Web Viewer.
6. If a Windows Security Alert pop-up appears, click “Unblock”.
7. After installing the KT&C Web View ActiveX Control, a Login page will be displayed.
Enter the user ID and password.
Note:
Default User ID and Password is [ID: admin, Password: admin]
8. The video image displays in your browser.
Note:
To view streaming video in Microsoft Internet Explorer, you must set your browser to allow the “KT&C Web
Viewer” to be installed on your computer. This ActiveX component is installed the first time a video stream is
accessed.
6. Terminal Block Connectors
KNC-Xi210HD is connected with external equipment as following diagram below.
Circuit diagram
1. INPUT – Connect the external sensor e.g. PIR motion sensor. (3.3V DC pull-up built in)
A. ON - Short-circuit with GND.
B. OFF - Open
CAUTION : Digital Input must not be exposed to voltages greater than 10V DC.
2. OUT – Connect the external alarm e.g. light or buzzer.
CAUTION : If used with an external relay, a diode must be connected in parallel
with the load, for protection against voltage transients.
CAUTION : Max. load = 70mA Max voltage = 12V DC.
Example of terminal connection
KNC-Xi120HD
SD Card
Microphone
Speaker
DC12VorAC24V
Adaptor
Reset Switch/
NTSC or PAL select