Chapin 19149 - Manual

Hazard: Improper use or failure to follow instructions can result in explosive failure causing
serious eye or other injury. For safe use of this product you must read and follow all instructions.
Do not leave a pressurized sprayer in the hot sun. Heat can cause pressure build-up. Do not store
or le ave solution in tank after use. Always wear goggles, gloves, long sleeve shirt, long pants and full
foot protection when spraying. Never use any tool to remove pump if there is pressure in sprayer.
Never stand with face or body over top of tank when pumping or loosening pump to prevent eject-
ing pump assembly and/or solution from striking and injuring you. Never pressurize sprayer by any
means other than the original pump. Do not attempt to modify or repair this product except with
original manufacturer’s parts. Never spray flammable materials or heat, pressure, or gas produc-
ing chemicals. Always read and follow manufacturer’s instructions before use with this sprayer
as some chemicals may be hazardous when used with this sprayer.
WARNING!
Sk-1113-1
Repair Parts Kit Gaskets and Seals (not included),
Juego de piezas de reparación, empaquetaduras y juntas (no incluido)
Kit de pièces de réparation, joints et garniture d’étanchéité (non inclus) 6-4629
1) Do: Check tightness of hose nut to be sure hose is securely attached to the tank outlet.
2) Do: Inspect hose for deterioration, cracks, softness, or brittleness. If any of these conditions are
found, replace hose before using. Replace with original manufacturer’s parts only.
3) Do: Remove pump (see Filling, Pressurizing and Spraying Instructions), inspect interior and
exterior of tank for signs of deterioration of body and bottom. Any sign of deterioration
indicates possible tank weakening and could result in explosive bursting under pressure. If
any of these signs are found, discard tank immediately and replace. Do not attempt to patch
leaks, etc., as this could result in serious injury.
4) Do: Follow Filling, Pressurizing and Spraying Instructions, except use water only.
5) Do: Pump plunger 10-20 strokes and inspect for leaks.
6) Do: Direct shut-off away from you and open to make sure discharge is not clogged.
7) Do: If unit passes this test, release pressure (see Pressure Releasing Instructions), empty tank,
and proceed with Filling, Pressurizing and Spraying Instructions.
3. Pre-Use Check
4. Filling
1) Do: Turn pump handle counterclockwise and remove pump
2) Do: Prepare spray solution following all directions and safety warnings on chemical label.
3) Do: Fill tank to no more than the proper gallon marker. Do NOT: overfill to accommodate
pump.
4) Do: Check pump to make sure that no grass or dirt is stuck to barrel. Replace pump in tank
and tighten securely.
8. Care, Storage and Maintenance
1) Do: Rinse tank thoroughly with water only, empty, refill with water. Follow Filling,
Pressurizing and Spraying Instructions, except pump unit only 8-10 strokes.
2) Do: Open shut-off and allow water to run through discharge assembly.
3) Do: Release pressure (Follow Pressure Release Instructions), remove pump and empty sprayer.
4) Do: Store sprayer tank upside down, with pump removed, in a warm dry location.
5) Do: Periodically oil pump by dropping 10-12 drops of light oil down pump rod through opening in cover.
WARNING: Handling the brass parts of this product will expose you to lead, a chemical known
to the State of California to cause birth defects and other reproductive harm. Wash hands after
handling.
011533-1 (A) R0000
1. Hose to Tank
2. Nozzle
Parts, Piezas, Pièces
Note: Your particular sprayer may not include all parts pictured above.
Nota: Es posible que este pulverizador en particular no incluya todas las partes que se ilustran arriba.
Remarque : Votre pulvérisateur particulier pourrait ne pas inclure toutes les pièces illustrées plus haut.
Attach the hose by screwing the swivel nut
clockwise and tightening to 37 in. lbs. Refer
to Pre-use check before using.
6-5373
Holster
Funda
Étui
6-8136
Valve Kit
Kit de la válvula
Ensemble de soupape
6-8135
Dripless Shut-off
Cierre antigoteo
Arrêt anti-goutte
Attach nozzle to shut-off handle or extension wand.
TO LOCK HANDLE: Push handle down to
depress coil spring and turn handle 1/4 turn
clockwise, then allow handle to raise into lock
position.
5A
Lock
Position
5B
TO RELEASE HANDLE: Push down to
depress coil spring and turn handle counter-
clockwise 1/4 turn, then lift handle.
Pump until you feel
resistance.
TO LOCK PUMP: Place pump prongs down into
slots in funnel, turn clamp clockwise to furthest
position under bottom slot, then turn handle
clockwise until tightly locked and sealed in place.
TO UNLOCK PUMP: Turn handle counterclockwise
until 3-prong clamp is loose. Then rotate clamp counter-
clockwise to stop and lift out.
5C
5D
5. Pressurizing and Spraying
5E
5F
1A
2A
For safety lock-off feature (no-spraying), push trigger
forward and rotate locking mechanism into lock-off
position as shown in fig. 6A.
6. Lock Off
7. To Release Pressure
1 Do: With pump facing away, turn locked handle counterclockwise until air begins to escape.
Stop turning handle when you hear air escaping.
2) Do: Stay away from the sprayer until all air has escaped.
6-6091
Hose Brown
Manguera Castaño
Tuyau Brun
6-5943
Nozzle 1.0 GPM
Tobera
Buse
6-5797
Nozzle .5GPM
Tobera
Buse
6A
Congratulations!
You have just purchased a quality Chapin product.
Register Your Sprayer Online @ www.chapinmfg.com
Questions?
Do Not Return To Store.
Call us @ 1-800-950-4458 or www.chapinmfg.com
¡
Felicitaciones!
Usted acaba de adquirir un producto de calidad Chapin.
Registre su pulverizador en línea en www.chapinmfg.com
¿Preguntas?
No regrese a la tienda;
llámenos al 1-800-950-4458 o visite www.chapinmfg.com
Félicitations!
Vous avez acheté un produit de qualité Chapin.
Enregistrez dès que possible votre pulvérisateur en ligne à l'adresse suivante:
www.chapinmfg.com
Questions ?
Ne retournez pas au magasin.
Appelez-nous 1-800-950-4458 ou visitez le www.chapinmfg.com
2B
6-6092
Hose Black
Manguera para trabajos pesados Negro
Tuyau pour service intense Noir
Valve Seat
Nozzle Adapter
Nozzle
To attach nozzle to shut-off, unthread nozzle adapter and re-
move valve seat from extension (2B). Unthread brass extension
nut and metal rod (2D). Assemble valve seat to shut-off then
assemble nozzle adapter as shown in figure (2A).
Note orientation of valve seat. It will leak if assembled wrong .
2C
Lock
Trigger
Metal Rod Brass Extension
OR
Brass Extension Nut
Metal Rod
2D
Metal Rod