Chapin 21127XP User Manual

Warning, Lock off, Nozzle

Advertising

Valve

Seat

Nozzle Adapter

Nozzle

WARNING

3. Pre-Use Check

4. Filling

1) Do: Turn pump handle counterclockwise and remove pump

2) Do: Prepare spray solution following all directions and safety warnings on chemical label.

3) Do: Fill tank to no more than the proper gallon marker. Do NOT: over fill to accommodate pump.

4) Do: Check pump to make sure that no grass or dirt is stuck to barrel. Replace pump in tank and tighten

securely.

9. Care, Storage and Maintenance

011534-3 (A) R0412

P.O. Box 549 700 Ellicott St.
Batavia, NY 14021-0549 U.S.A.
1-800-950-4458 www.chapinmfg.com

WARNING:

Handling the brass parts of this product will expose you to lead, a chemical known to the State

of California to cause birth defects and other reproductive harm. Wash hands after handling.

1. Hose to Tank

Discharge/ Assembly

• Make sure white outlet tube is attached to outlet tube adapter (Fig. 1A).

• Insert the outlet tube portion of the discharge assembly into the tank adapter (Fig. 1B).

• Proper placement of white outlet tube (Fig. 1C).

• Firmly insert the outlet tube adapter into the tank adapter (Fig. 1D) Lining up tab

with notches on the tank adapter.

• Firmly tighten the retaining nut to the tank adapter (Fig. 1E).

Discharge

Assembly

Outlet

Tube

Retaining Nut -

Securely tightened.

Gap

Tank

Adapter

Outlet Tube

Adapter

Tab/

Notch

Outlet Tube

Adapter

Outlet

Tube

Parts, Piezas, Pièces

Repair Parts Kit Gaskets and Seals (not included),

Juego de piezas de reparación, empaquetaduras y juntas (no incluido)

Kit de pièces de réparation, joints et garniture d’étanchéité (non inclus)

6-4601

Note:

Your particular sprayer may not include all parts pictured above.

Nota:

Es posible que este pulverizador en particular no incluya todas las partes que se ilustran arriba.

Remarque :

Votre pulvérisateur particulier pourrait ne pas inclure toutes les pièces illustrées plus haut.

Congratulations!

You have just purchased a quality Chapin product.

Questions?

Do Not Return To Store.

Call us @ 1-800-950-4458 or www.chapinmfg.com

¡Felicitaciones!

Usted acaba de adquirir un producto de calidad Chapin.

Registre su pulverizador en línea en www.chapinmfg.com

¿Preguntas?

No regrese a la tienda;

llámenos al 1-800-950-4458 o visite www.chapinmfg.com

Félicitations!

Vous avez acheté un produit de qualité Chapin.

Enregistrez dès que possible votre pulvérisateur en ligne à l'adresse

www.chapinmfg.com

Questions ?

Ne retournez pas au magasin.

Appelez-nous 1-800-950-4458 ou visitez le www.chapinmfg.com

6-6090

Hose Black

Manguera para trabajos

pesados Negro

Tuyau pour service

intense Noir

For safety lock-off feature (no-spraying), push trigger forward

and rotate locking mechanism into lock-off position as shown

in fig. 6A.

6. Lock Off

6-8136

Valve Kit

Kit de la válvula

Ensemble de soupape

6-8135

Dripless Shut-off

Cierre antigoteo

Arrêt anti-goutte

2. Nozzle

Attach nozzle to shut-off handle

or extension wand. Hand tighten

nozzle adapter. Tighten with wrench.

Note orientation of valve seat. It will leak if assembled wrong .

Metal Rod

Brass Extension

Brass Extension Nut

Metal Rod

Lock

Trigger

1) Do: Check tightness of hose nut to be sure hose is securely attached to the tank outlet.

2) Do: Inspect hose for deterioration, cracks, softness, or brittleness. If any of these conditions are found, replace hose

before using. Replace with original manufacturer’s parts only.

3) Do: Remove pump (see Filling, Pressurizing and Spraying Instructions), inspect interior and exterior of tank for signs of

deterioration of body and bottom. Any sign of deterioration indicates possible tank weakening and could result in

explosive bursting under pressure. If any of these signs are found, discard tank immediately and replace. Do not attempt

to patch leaks, etc., as this could result in serious injury.

4) Do: Follow Filling, Pressurizing and Spraying Instructions, except use water only (Pump plunger 10-20 strokes and

inspect for leaks).

5) Do: Direct shut-off away from you and open to make sure discharge is not clogged.

6) Do: If unit passes this test, release pressure (see Pressure Releasing Instructions), empty tank, and proceed with Filling,

Pressurizing and Spraying Instructions.

7) Do: Inspect all metal parts including the wand, nozzle and fittings for rust, corrosion and pitting. If any of these

conditions are found, replace affected part with original manufacturer’s part before using.

1) Do: Rinse tank thoroughly with water only, empty, refill with water. Follow Filling, Pressurizing and

Spraying Instructions, except pump unit only 8-10 strokes. Be sure that the wand and nozzle are

thoroughly rinsed with water after each use.

2) Do: Open shut-off and allow water to run through discharge assembly.

3) Do: Release pressure (Follow Pressure Release Instructions), remove pump and empty sprayer.

4) Do: Store sprayer tank upside down, with pump removed, in a warm dry location.

5) Do: Periodically oil pump by dropping 10-12 drops of light oil down pump rod through opening

in cover.

WARNING: Improper use or failure to follow instructions can result in explosive failure causing serious

eye or other injury.

For safe use of this product you must read and follow all instructions. Do not leave a pres-

surized sprayer in the hot sun. Heat can cause pressure build-up resulting in possible explosion. Do not store

or leave solution in tank after use. Always wear goggles, gloves, long sleeve shirt, long pants and full foot protec-

tion when spraying. Never use any tool to remove pump if there is pressure in sprayer. Never stand with face or

body over top of tank when pumping or loosening pump to prevent ejecting pump assembly and/or solution

from striking and injuring you. Never pressurize sprayer by any means other than the original pump. Do not

attempt to modify this sprayer. Replace parts only with manufacturer’s original parts. This sprayer is intended

for Acetone only. Acetone is extremely flammable. This Acetone sprayer is intended for trained profes-

sionals only- Not intended for the retail trade. Always read and follow chemical manufacturer’s instruc-

tions before use with this sprayer as some chemicals may be hazardous when used with this sprayer.

Sk-1169-1

6-1929

Nozzle & Brass Adapter

Tobera

Buse

5. Pressurizing and Spraying

Do:

Turn handle clockwise to

tighten. Push handle down,

turn 1/4 turn counterclock-

wise to release.

Do:

Pump until you

feel resistance.

Do:

Push handle, down, turn

1/4 turn clockwise to lock. Begin

spraying. Re-pump sprayer as

required to maintain spray force.

7. To Release Pressure

1) Your sprayer is equipped with a pressure relief/release valve

(Fig. 7A). To release pressure lift and hold the cap until air

is completely exhausted, OR, turn the valve slowly counter

clockwise until you hear air escaping and wait air is completely

exhausted (Fig. 7B).

2) Do: Stay away from the sprayer until all air has escaped.

8. Wand Dock Clip

Choose the holder that fits your wand.

6-4608

Pressure Relief Valve

Válvula de descarga de presión

Soupape de décompression

301630-2

Pump Assembly

Asamblea de la bomba

Assemblée de pompe

Advertising

Popular Brands

Popular manuals