Chapin 22190 - Manual

WARNING!
Printed in U.S.A.
1) Do: Check tightness of hose nut to be sure hose is securely attached to the tank outlet.
2) Do: Inspect hose for deterioration, cracks, softness, or brittleness. If any of these conditions are found, replace hose
before using. Replace with original manufacturer’s parts only.
3) Do: Remove pump (see Filling, Pressurizing and Spraying Instructions), inspect interior and exterior of tank for signs
of deterioration of body and bottom. Any sign of deterioration indicates possible tank weakening and could result in
explosive bursting under pressure. If any of these signs are found, discard tank immediately and replace. Do not
attempt to patch leaks, etc., as this could result in serious injury.
4) Do: Follow Filling, Pressurizing and Spraying Instructions, except use water only.
5) Do: Pump plunger 8-10 strokes and inspect for leaks.
6) Do: Direct shut-off away from you and open to make sure discharge is not clogged.
7) Do: If unit passes this test, release pressure (see Pressure Releasing Instructions), empty tank, and proceed with Filling,
Pressurizing and Spraying Instructions.
3. Pre-Use Check
4. Filling
1) Do: Turn pump handle counterclockwise and remove pump
2) Do: Prepare spray solution following all directions and safety warnings on chemical label.
3) Do: Fill tank to no more than the proper gallon marker. Do NOT: over fill to accommodate pump.
4) Do: Check pump to make sure that no grass or dirt is stuck to barrel. Replace pump in tank and tighten securely.
5. Pressurizing and Spraying
Do: Turn handle clockwise to
tighten. Push handle down, turn
1/4 turn counterclockwise to
release.
Do: Pump until you
feel resistance.
Do: Push handle, down, turn 1/4 turn
clockwise to lock. Begin spraying. Re-
pump sprayer as required to maintain
spray force.
7. To Release Pressure
1) Your sprayer is equipped with a pressure relief/release valve. To release pressure lift
and hold the cap until air is completely exhausted, OR, turn the valve slowly counter-
clockwise until you hear air escaping and wait air is completely exhausted.
2) Do: Stay away from the sprayer until all air has escaped.
8. Care, Storage and Maintenance
1) Do: Rinse tank thoroughly with water only, empty, refill with water. Follow Filling, Pressurizing and Spraying
Instructions, except pump unit only 8-10 strokes.
2) Do: Open shut-off and allow water to run through discharge assembly.
3) Do: Release pressure (Follow Pressure Release Instructions), remove pump and empty sprayer.
4) Do: Store sprayer tank upside down, with pump removed, in a warm dry location.
5) Do: Periodically oil pump by dropping 10-12 drops of light oil down pump rod through opening in cover.
010538-2 (A) R0209
5A 5C
1. Hose to Tank
5B
Make sure white outlet tube
is attached to hose.
Insert tube into tank.
WARNING: Handling the brass parts of this product will expose you to lead, a chemical known
to the State of California to cause birth defects and other reproductive harm. Wash hands after
handling.
2. Nozzle
1A 1B
Proper placement of white
outlet tube.
1C
Line up tabs on safety lock
connector with notches
on the outlet flange of
the tank. Insert tabs into
notches to form a secure
seal.
Slip hose nut down to
tank, turnclockwise
and tighten as tight as
possible by hand.
1E
Hazard: Improper use or failure to follow instructions can result in explosive failure causing
serious eye or other injury. For safe use of this product you must read and follow all instructions.
Do not leave a pressurized sprayer in the hot sun. Heat can cause pressure build-up. Do not store or
le ave solution in tank after use. Always wear goggles, gloves, long sleeve shirt, long pants and full foot
protection when spraying. Never use any tool to remove pump if there is pressure in sprayer. Never
stand with face or body over top of tank when pumping or loosening pump to prevent ejecting pump
assembly and/or solution from striking and injuring you. Never pressurize sprayer by any means
other than the original pump. Do not attempt to modify or repair this product except with original
manufacturer’s parts. Never spray flammable materials or heat, pressure, or gas producing chemi-
cals. Always read and follow manufacturer’s instructions before use with this sprayer as some
chemicals may be hazardous when used with this sprayer.
Sk-1113-1
6-6136
Hose
Manguera
Tuyau
6-1898
Shut-off Handle
Mango de cierre
Poignée du robinet
6-3337
Straps
Tirantes
Sangles
For constant spraying, push down on shut-off handle and move locking
mechanism away from you. To release, squeeze handle and move the locking
mechanism back towards you.
6. Fatigue-Free Spraying
Note: Your particular sprayer may not include all parts pictured above.
Nota: Es posible que este pulverizador en particular no incluya todas las partes que se ilustran arriba.
Remarque : Votre pulvérisateur particulier pourrait ne pas inclure toutes les pièces illustrées plus haut.
1D
Attach nozzle to shut-off handle or extension wand.
Parts, Piezas, Pièces
6-6141
Hose Brown
Manguera Castaño
Tuyau Brun
6-5943
Nozzle 1.0 GPM
Tobera
Buse
6-7734
Extension wand, Vara de extensión, Rallonge
6-5797
Nozzle .5GPM
Tobera
Buse
6-7749
Extension wand, Vara de extensión, Rallonge
6-4638
Shut-off Handle
Mango de cierre
Poignée du robinet
6-6003
Nozzle
Tobera
Buse
6-000
Nozzle
Tobera
Buse
3-7727
Extension wand, Vara de extensión, Rallonge
Pull handle
straight up.
Insert notches from underside
of handle into plunger grooves
and turn counterclockwise.
Remove plunger and diaphragm. Clean
plunger, diaphragm and body. Flip
diaphragm and replace.
Tighten plunger clockwise until flush to top of
shut-off body. Do not over-tighten or unit may
not spray. Slide forks under plunger, push handle
down until it snaps into place.
9. Troubleshooting
- Tank pressurizes but does not spray.
9B
9A Handle
9C
Plunger
Body
Diaphragm
9D
Plunger flush
with body
WARNING: Release pressure in tank before troubleshooting.
Clean shut-off (Fig. 9A- 9D)
Clean Nozzle Assembly (Fig. 9E) -Remove nozzle cap. Clean and re-assemble.
9E
Nozzle Cap
Repair Parts Kit Gaskets and Seals (not included),
Juego de piezas de reparación, empaquetaduras y juntas (no incluido)
Kit de pièces de réparation, joints et garniture d’étanchéité (non inclus) 6-5368
6A
Locking
mechanism
6B
2A
2B
7A