CNB G1815PF User Manual

Digital slow shutter

Advertising

OFF

BLC OFF

AGC ON

D / N

DSS ON

D.Z OFF

FL OFF

ELC / DC

LEVEL V.PHASE

ELC

POWER

VIDEO OUT

Class 2 Only

AC 24V / DC 12V

F.G

OFF

BLC OFF

AGC ON

D / N

DSS ON

D.Z OFF

FL OFF

POWER

VIDEO OUT

ELC / DC

LEVEL

ELC

Class 2 Only

DC 12V

OFF

BLC OFF

AGC ON

D / N

DSS ON

D.Z OFF

FL OFF

ELC / DC

LEVEL V.PHASE

ELC

POWER

VIDEO OUT

Class 2 Only

AC 24V / DC 12V

F.G

OFF

BLC OFF

AGC ON

D / N

DSS ON

D.Z OFF

FL OFF

ELC / DC

LEVEL V.PHASE

ELC

POWER

VIDEO OUT

Class 2 Only

AC 24V / DC 12V

F.G

OFF

BLC OFF

AGC ON

D / N

DSS ON

D.Z OFF

FL OFF

POWER

VIDEO OUT

ELC / DC

LEVEL

ELC

POWER INLET

OFF

BLC OFF

AGC ON

D / N

DSS ON

D.Z OFF

FL OFF

ELC / DC

LEVEL V.PHASE

ELC

POWER

VIDEO OUT

Class 2 Only

AC 24V / DC 12V

F.G

OFF

BLC OFF

AGC ON

D / N

DSS ON

D.Z OFF

FL OFF

POWER

VIDEO OUT

ELC / DC

LEVEL

ELC

Class 2 Only

DC 12V

Notes

The lens is not supplied with this camera. Purchase a lens suitable
for your environment. This camera accepts the auto iris lens and
both C-and CS-mount lens.

Installing Auto Iris Lens

. If the lens is marked with fingerprints or other marks,

the image quality might be poor.

Notes

. Be sure to connect power after all the installation is done.
. Note that AC adaptor is not supplied with camera.
. Use only AC 24V/DC12V UL listed class 2 power supply.
. Do not use power sources other than that specified.

. It is recommended to use a high quality lens to improve the

image quality under low illumination.
. Use auto iris lens with DC type only.

3. Remove the cover from the iris lens plug supplied, and solder the

lens cable to the plug as shown below.

4. Remove the protective cap, and attach the lens to the camera by

turning clockwise.

5. Connect the lens plug to the auto iris connector on the right side

of the camera.

6. Set the DC/ ELC selection switch to DC or ELC according to the

type of the lens.

No. 3 Pin

No. 1 Pin

connector

Lens cable

No. 4 Pin

No. 2 Pin

Each model has different power specification, please check the name of
the model and power specification before connecting to power source.
Please refer to the sticker identifying the model, which is attached on the
product, for power specification.

For DC12V Power Type Only

. The wire is polarized. Be careful of polarity.

. Use DC 12V power source.

Resistance of copper wire [at 20℃ (68˚F)]

. Voltage drop may be experienced by the camera as per length of the power
cable according to the table above. The camera may malfunction of the
length of the output line between the camera and the adaptor is too long.

* Voltage for camera operation: DC 12V ± 10%
* Voltage drops on above table are variable according to types of electric
cord and makers.

Copper wire size

(AWG)

Resistance(Ω/m)

#18

(0.83㎟)

Voltage Drop(V/m)

#24

(0.22㎟)

#22

(0.33㎟)

#20

(0.52㎟)

0.078

0.050

0.030

0.018

0.028

0.018

0.011

0.006

For AC24V / DC12V Power Type

For AC100V~AC240V Power Type

. The wire is non-polarized.

. Use AC 24V power source or DC 12V power source.

OWNER'S MANUAL

Before operating the camera, confirm that you have the right
camera model and proper power voltage.
In order to help you understand this manual, we'll introduce
our model's description.

Thank you for purchasing this COLOR VIDEO CAMERA.

1. Model Description

If you have trouble operating your camera, refer to the following table.
If the guidelines do not enable you to solve the problem, contact an
authorized technician.

Problem

Solutions

Nothing appears on
the screen.

The image on the
screen is dim.

The image on the
screen is dark.

The camera is not
working properly,
and the surface of
the camera is hot.

The image on the
screen flickers.

• Check that the power cord and line connection
between the camera and monitor are fixed properly.
• Check that you have properly connected VIDEO
cable to the camera VIDEO output jack.

• Is lens stained with dirt? Clean your lens with soft,
clean cloth.
• Set the monitor to proper condition.
• If the camera is exposed to too strong light, change
the camera position.
• Adjust the lens' focus properly.

• Adjust the contrast feature of the monitor.
• If you have an intermediate device, set the 75Ω/ Hi-z
properly. (refer to page 18)
• Adjust DC Level, VR Level properly. (refer to page 10, 11)

• Check that you have properly connected the camera
to an appropriate power source.
(refer to page 16-17)

• Is the camera facing to direct sunlight or fluoresent
lighting? Change the camera position.

8. Troubleshooting

Do use the camera under conditions where temperatures are within
-10°C to 45°C. Especially be careful for ventilation under high temperature.

Do not install the camera in extreme temperature conditions.

Do not install or use the camera in an environment where the

humidity is high.

It can cause the image quality to be poor.

Do not install the camera under unstable lighting conditions.
Severe lighting change or flicker can cause the camera to work improperly.

Never use the camera close to a gas or oil leak.

It can cause malfunctions to occur.

Do not disassemble the camera.

There are no user-serviceable parts inside it.

It can cause malfunctions to occur.

Do not drop the camera or subject them to physical shocks.

Never keep the camera face to strong light directly.

It can damage CCD.

Do not expose the camera to rain or spill beverage on it.

If it gets wet, wipe it dry immediately. Liquids can contain minerals that
corrode the electronic components.

Note
When this camera is installed near wireless communication
devices that emits strong electromagnetic field, irregularity
such as noise on the monitor may appear.

Features

3. Composition

6. Connection

. Contents

Model Description

Precautions

Composition

Features

Name and Function

Connection

Specifications

Troubleshooting

. User Information

CAUTION! TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

Explanation of two Symbols

The lightning flash with arrowhead symbol,

within an equilateral triangle, is intended to

alert the user to the presence of un-insulated

"dangerous voltage" within the product's

The exclamation point within an equilateral

triangle is intended to alert the user to the

presence of important operating and

maintenance-(servicing) instructions in the

THE GRAPHIC SYMBOLS WITH SUPPLEMENTAL MARKING ARE
ON THE BOTTOM OF THE SYSTEM.

"WARNING-TO PREVENT FIRE OR SHOCK HAZARD, DO NOT
EXPOSE THE UNIT TO RAIN OR MOISTURE"

enclosure that may be of sufficient magnitude to constitute a

risk of electric shock to persons.

literature accompanying the appliance.

2. Precautions

Pin.No.

1
2
3
4

DC TYPE

--- Damping -
--- Damping +

--- Drive +
--- Drive -

For BNC Video Output Model

Connect the VIDEO out jack to the monitor video in jack.

Camera

CCD Camera

Intermediate

Video Receiver

End monitor

As the connecting method varies with the instruments, refer to the
manual supplied with the instrument.

Connect the cable after power is turned off.

Set the 75Ω/ Hi-Z selection switch as shown below if you have an
intermediate device.

Monitor

LENS

Connecting to Power

Connecting to Monitor

COLOR VIDEO CAMERA

7. Specifications

-DC 12V Input Model

7. Specifications

-AC 24V/DC 12V Input Model

7. Specifications

-AC 100V~AC 240V Input Model

. Memo

Color Video Camera Series

D&N(ICR)

X
X
X
X
X
X
O
O
O
O
O
O

Signal System

NTSC

PAL

NTSC

PAL

NTSC

PAL

NTSC

PAL

NTSC

PAL

NTSC

PAL

Power Input

DC 12V
DC 12V

AC 24V / DC 12V
AC 24V / DC 12V

AC 100V~AC 240V
AC 100V~AC 240V

DC 12V
DC 12V

AC 24V / DC 12V
AC 24V / DC 12V

AC 100V~AC 240V
AC 100V~AC 240V

6. DC/ MANUAL Lens Selectable

The camera accepts 2 types of lenses (DC/MANUAL) and is set with

the ELC/DC selection switch.

7. Electronic Iris

Electronic iris shutter is automatically controlled at the speed of

1/60 ~ 120,000sec (NTSC models),

1/50 ~ 120,000sec (PAL models).

3. High Sensitivity (Digital Slow Shutter)

This camera can detect automatically darkness or night and support

it to take a clear and bright image. As the grade of darkness, this

camera can accumulate up to 32 fields.

4. Day & Night Function

This camera can switch to the COLOR mode to support the best

color image in the day time and switch to the B/W mode for the clear

image in the night time.

5. Digital Zoom Function

This camera can magnify its image in a distance.

On the mode of D-ZOOM, it magnifies twice(x2) than the real image.

1. High Resolution

The horizontal resolution of 550 TV lines can be achieved by

using a high density CCD having effective 410K pixels, which provides

clean, noiseless and reliable pictures.

2. SDNR (Super Digital Noise Reduction)

By SDNR, this camera can reduce video noise, and improve the S/N

ratio. By this technology, this camera can show the clear and exact

image even in a gloomy place.

High Resolution

Model

Signal System
CCD Pick-up Element
Effective Pixels
Video Output
Sync. System
Luminance S/N Ratio
Resolution
Sensitivity (F1.2)
Lens Mount
Electronic Shutter
White Balance
Auto Gain Control
Back Light Compensation
Day & Night
Flickerless
Digital Slow Shutter
D-ZOOM
Digital Noise Reduction
Operating Temperature
Storage Temperature
Supply Voltage
Power Consumption
Dimensions (WxHxD)
Weight

NTSC PAL

2:1 Interalce Transfer 1/3 Inch Super HAD CCD
768(H) x 494(V) 752(H) x 582(V)

Composite: 1.0V p-p, 75Ω

Internal Sync

50dB Min. (AGC OFF)

550 TV lines

0.3 Lux (Color)/ 0.1 Lux (B/W) / 0.008 Lux (DSS On, x32)

C / CS Mount

1/60 ~ 120,000 Sec. 1/50 ~ 120,000 Sec.

AWB

On / Off Selectable
On / Off Selectable
On / Off Selectable
On / Off Selectable

Max 32 Times

2 x

Auto

-10℃~+45℃
-20℃~+65℃

DC 12V (DC 9.6V ~ 13.2V)

150mA (Max)

65 x 59.6 x 122.5mm

Approx. 430g

High Resolution

Model

NTSC PAL

2:1 Interalce Transfer 1/3 Inch Super HAD CCD
768(H) x 494(V) 752(H) x 582(V)

Composite: 1.0V p-p, 75Ω

Internal Sync

50dB Min. (AGC OFF)

550 TV lines

0.3 Lux (Color)/ 0.1 Lux (B/W) / 0.008 Lux (DSS On, x32)

C / CS Mount

1/60 ~ 120,000 Sec. 1/50 ~ 120,000 Sec.

AWB

On / Off Selectable
On / Off Selectable
On / Off Selectable
On / Off Selectable

Max 32 Times

2 x

Auto

-10℃~+45℃
-20℃~+65℃

AC 100V ~ AC 240V

3W (Max)

65 x 59.6 x 122.5mm

Approx. 430g

High Resolution

Model

NTSC PAL

2:1 Interalce Transfer 1/3 Inch Super HAD CCD
768(H) x 494(V) 752(H) x 582(V)

Composite: 1.0V p-p, 75Ω

Internal Sync

50dB Min. (AGC OFF)

550 TV lines

0.3 Lux (Color)/ 0.1 Lux (B/W) / 0.008 Lux (DSS On, x32)

C / CS Mount

1/60 ~ 120,000 Sec. 1/50 ~ 120,000 Sec.

AWB

On / Off Selectable
On / Off Selectable
On / Off Selectable
On / Off Selectable

Max 32 Times

2 x

Auto

-10℃~+45℃
-20℃~+65℃

AC 24V (20V ~ 28V) or DC 12V (10V ~ 15V)

3W (Max)

65 x 59.6 x 122.5mm

Approx. 430g

Cabel

- Brown
- Blue
- Green

AC Power Input

Frame Ground

1. Color Video Camera ...................

2. Auto Iris Lens Plug .....................

3. C-Mount Adapter ........................

4. Owner's Manual .....................

DIGITAL CAMERA SERIES

COLOR VIDEO CAMERA

INFORMATION

This equipment has been tested and found to comply with limits for a
Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial
environment.
This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instruction manual,
may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct
the interference at their own expense.

WARNING

The manufacturer could void the user's authority to operate the
equipment.

CAUTION - To prevent electric shock and risk of fire hazards:

Do NOT use power sources except for that specified.
Do NOT expose this appliance to rain or moisture.

This installation should be made by a qualified service person
and should abide to all local codes.

AC 24V/DC 12V Input Model

③ V.PHASE

Adjustment V.R

① Function

Selection

⑥ Video Out Jack

④ ELC/DC LEVEL

Adjustment V.R

② Lens Selection

Swicth

⑤ Power Input

Terminal

Left( ):Internal
Right( ):External

DC 12V Input Model

① Function

Selection

⑥ Video Out Jack

④ ELC/DC LEVEL

Adjustment V.R

② Lens Selection

Swicth

⑤ Power Input

Terminal

AC 100V~AC 240V Input Model

① Function

Selection

⑤ Power AC IN

⑥ Video Out Jack

④ ELC/DC LEVEL

Adjustment V.R

② Lens Selection

Swicth

AC24V/DC12V

Class 2 Only

F.G

DC 12V

Class 2 Only

P/N : 3810-0086C

(Ver.0610E)

Color Video Camera Series

SDNR Camera Series

Digital Slow Shutter

Design and specifications
are subject to
change without notice.

High Resolution

DSS

Super Digital Noise Reduction

SDNR

① Function Selection Switch

② Lens Selection Switch

Used to choose DC or ELC according to the type of your Lens.
③ V.PHASE Adjustment V.R (AC 24V / DC 12V Input Model)

If the camera is to be used in LineLock mode, the vertical phase may require

adjustment to synchronize the vertical phase of the camera with other camera

in the system. Make this adjustment when the vertical phase of the camera

does not match with other cameras or systems. For correct adjustment,

use a multi-channel oscilloscope. The V.PHASE adjustment can be readjusted.
④ ELC / DC LEVEL Adjustment V.R

Used to adjust video output level of DC driven auto iris lens or ELC mode.

When the brightness control of the monitor does not operate correctly.
⑤ POWER Input Terminal

Used to connect an AC 24V or DC 12V power source.

Used to connect a DC 12V power source.

Used to connect an AC 100V~AC 240V power source.
⑥ VIDEO OUT Jack: Use for installation and service.

FL (Flickerless)

If the camera is used with 50Hz fluorescent lighting,

there maybe flicker on the screen. In this case, FL switch

should be set to ON position. But, FL switch should be

set to OFF position if 60Hz power source is used.

AGC (Automatic Gain Control)

With AGC ON, the setting, camera's sensitivity is

automatically increased when the level of ambient light

drops. AGC function automatically controlls signal gain

in the range of maximum 28dB.

D/N (Day & Night ON/OFF)

This camera can switch to the COLOR mode to support

the best color image in the day time and switch to the

B/W mode for the clear image in the night time.

DSS (Digital Slow Shutter)

This camera can detect automatically darkness or night and

support it to take a clear and bright image. As the grade

of darkness, this camera can accumulate up to 32 fields.

D-ZOOM (Digital Zoom)

This camera can magnify its image in a distance.

On the mode of D-ZOOM, it magnifies twice (x2) than

the real image.

BLC (Back Light Compensation)

This feature would be useful when camera is facing an

object that has excessive light behind it. BLC prevents

the center of object from too much darkness.

E.g.: Video camera in the store facing the entrance doors.

OFF

BLC OFF

AGC ON

D / N

DSS ON

D.Z OFF

FL OFF

OFF

BLC OFF

AGC ON

D / N

DSS ON

D.Z OFF

FL OFF

OFF

BLC OFF

AGC ON

D / N

DSS ON

D.Z OFF

FL OFF

OFF

BLC OFF

AGC ON

D / N

DSS ON

D.Z OFF

FL OFF

OFF

BLC OFF

AGC ON

D / N

DSS ON

D.Z OFF

FL OFF

OFF

BLC OFF

AGC ON

D / N

DSS ON

D.Z OFF

FL OFF

OFF

BLC OFF

AGC ON

D / N

DSS ON

D.Z OFF

FL OFF

POWER

VIDEO OUT

ELC / DC

LEVEL

ELC

POWER INLET

OFF

BLC OFF

AGC ON

D / N

DSS ON

D.Z OFF

FL OFF

ELC / DC

LEVEL V.PHASE

ELC

POWER

VIDEO OUT

Class 2 Only

AC 24V / DC 12V

F.G

•

igi

tal

w S

tte

•S

•

550

TVL

Digital Slow Shutter

High Resolution

DSS

OWNER'S MANUAL

DIGITAL CAMERA SERIES

COLOR VIDEO CAMERA

Super Digital Noise Reduction

SDNR

•

ita

l S

w S

tte

•S

tio

n •

550 TVL

Name and Function

CS-Mount Holding Screw

Used to readjust back focus of the camera. There are two back

focus lock screws. These must be loosened before the camera

may be back focused.

Loosen the lock screws to turn the CS-mount lens adaptor, and

tighten the lock screws after adjustment.

Tripod Mounting Hole

Used to install the camera on an optional tripod. The tripod

must be equipped with the screw specified as shown below.

Auto Iris Lens Connector

Used to connect Auto Iris Lens plug.

C-Mount Lens Adapter

Used to attach C-mount lens.

CS-Mount Lens Adapter

Used to attach CS-mount lens.

1/4"- 20 UNC (20 THREAD)

L : 4.5mm±0.2mm (ISO standard),

or 0.197" (ASA standard)

1. Peel approximately 8mm from the end of the lens cable outer
cover.

2. Peel approximately 2mm from the end of the cable inner cover.

8mm

Installing C/CS-Mount Lens

Notes

Before mounting a lens, please check whether it is a C-mount or
CS-mount lens.
The back focus is set for the CS-mount lens at the factory.

Mounting a CS-Mount Lens
After removing the protecting cap, attach the lens into the camera
by turning clockwise.

. Use the lens under the specification as shown. Otherwise the

lens can damage the camera or abnormal fixing may result.

. A heavy lens may disturb the balance with the camera and

possibly result in damage. Don't use a lens heavier than 450g.
. It is recommended to set the lens ALC mode to Av mode(Average).

Pk mode can be occurred hunting.

C-mount lens : 10mm or less

CS-mount lens : 5mm or less

1. Attach the C-Mount lens adapter by turning clockwise.

2. Attach the lens to the camera by turning clockwise.

Mounting a C-Mount Lens

Advertising

This manual is related to the following products:

G1815NF

Popular Brands

Popular manuals