CNB V3810PF - Manual

Signal System
Scanning System
Scanning Frequency (H)
Scanning Frequency (V)
Image Sensor
Total/Effective Pixels No.
S/N Ratio
Resolution
Video Output Level
Lens
Focus
Sync. System
Sensitivity
Electronic Shutter
White Balance
AGC
Input/Output Connector
Power Consumption
(Option: AC 24V/DC 12V)
Dome Size (Ø) NTSC : 525 Lines PAL : 625 Lines
2 : 1 Interlace
15.734kHz 15.625kHz
59.94Hz 50Hz
1/3 inch SONY Super HAD CCD
410K/380K [Normal:270K/250K] 470K/440K[Normal:320K/290K]
More than 48dB
550 TV Lines / 480 TV Lines / 380 TV Lines
1.0 Vp-p (75 Ohms, composite)
Fixed Lens (f=3.8mm, 6.0mm Selectable)
Manual
Internal
0.3 Lux(High) / 0.1 Lux(Normal)
1/60~10,000 Sec. 1/50~10,000 Sec.
Auto
Auto
Power(Red or Green Jack), Video(Yellow Jack)
DC 12V (DC 9V~15V) / 3W (Max)
AC 24V (20V~28V) or DC 12V (10V~15V), 5W (Max)
68mm / 85mm
!
USER INFORMATION:
PRECAUTION:
Design and specifications
are subject to change
without notice.
CAUTION! TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
All the warnings and instructions of this manual should be followed.
Keep enough space around the unit for ventilation.
Slots and openings on the monitor should not be blocked.
During flashes of lightning or cracks of thunder, or when the system
is not used for a long time, unplug the system power supply to
protect the unit from lightening or power surges.
Do not attempt to service this unit yourself as opening or removing
covers may you to dangerous voltage or other hazards. Please refer
all servicing to qualified service personnel.
Do not place anything on top of the unit that might spill or fall into it.
To reduce the risk of fire or electric shock, do not expose this appliance
to rain or moisture.
Remove the plug from the outlet before cleaning. Do not use liquid
aerosol detergents. Use water damped cloth for cleaning.
THE GRAPHIC SYMBOLS WITH SUPPLEMENTAL MARKING ARE ON THE BOTTOM
OF THE SYSTEM.
"WARNING-TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THE UNIT
TO RAIN OR MOISTURE"
The lightning flash with arrowhead symbol, within an equilateral
triangle, is intended to alert the user to the presence of un-insulated
"dangerous voltage" within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to
alert the user to the presence of important operating and maintenance-
(servicing) instructions in the literature accompanying the appliance.
Explanation of two Symbols
No.
#1
#2
Function
Video Output
Power Input
Remark
1.0 Vp-p
AC24V(20V~28V) or
DC12V(10V~15V),5W(Max)
Terminal Color
Yellow
Green
• The wire is non-polarized.
• Use AC 24V power source or
DC 12V power source.
AC 24V/DC 12V Power Type
Video Output
GND
Video
(Yellow)
Power - AC 24V/ DC 12V
(Green)
No.
#1
#2
Function
Video Output
Power Input
Remark
1.0 Vp-p
DC12V(10V~15V),
3W(Max)
Terminal Color
Yellow
Red
• The wire is polarized.
• Use DC 12V power source.
DC 12V Power Type
Video Output
GND
Video
(Yellow)
Power - DC 12V
(Red)
P/N:3810-0084A
ver.0611E ※ AC 24V / DC 12V: Ø85 Only
※ AC 24V / DC 12V: Ø85 Only
CONNECTION:
Dome (Ш68), (Ш85)
SPECIFICATIONS:
The image does
not appear on the
screen.
Check the power source for the monitor
and camera and assure that the voltage
and polarity are properly connected and
being supplied correctly.
The image on the
screen is dim.
Check if the lens is stained. If dirty,
clean the lens with a soft, clean cloth.
Adjust the Back Focus of the lens again.
The camera does
not work properly,
the surface of the
camera case is hot,
and a black line
a p p e a r s o n t h e
screen.
Check if you have connected the camera
to a proper power source and If there is
no problem with the power, turn the unit
off immediately and seek assistance from
our After Service department.
The screen blinks
a lot.
Check if the camera is pointed toward
the sun or a fluorescent lamp.
Adjust the angle or location of the
camera if too much light is coming into
the screen.
TROUBLESHOOTING:
If you have trouble operating your camera, refer to the following.
If the guidelines do not enable you to solve the problem,
contact an authorized technician.
COMPOSITION: You must be fully aware of all the
distinctive features and precautions
related to this camera before installing it.
#1
#2
#1
#2
Ø 68
Vandal Resistant Dome Camera (Surface Type)
Owner's Manual
Guide Pattern
Mounting Screw
L-Wrench
Ø 68
Vandal Resistant Dome Camera (Flush Type)
Owner's Manual
Guide Pattern
Mounting Screw
L-Wrench
Ø 85
Vandal Resistant Dome Camera (Surface Type)
Owner's Manual
Guide Pattern
Mounting Screw
L-Wrench
camera color
CCD Camera Color Dome
Color Dome Digital DSP
1/3" SONY CCD
LENS
.Fixed Lens
D i g i t a l