CNB V2310PVF - Manual

camera color
1/3" SONY CCD
Design and specifications are
subject to change without notice.
Dome Camera Vandal Proof
Vandal Proof Digital DSP
LENS .Vari-focal
.Fixed Lens
3-Axis
• S
im
p l e
t o i n s t a l l 3 -
A
x i s
b
r a
c k e
t
m ak
es
ad ju st m en
t
e a s y
.
SPECIFICATIONS:
DIMENSIONS(mm):
COMPOSITION:
Model
Signal System
Scanning System
Scanning Frequency (H)
Scanning Frequency (V)
Image Sensor
Total / Effective Pixels No.
S / N Ratio
Resolution
Video Output Level
Lens
Focus
Sync. System
Sensitivity
Electronic Shutter
White Balance
AGC
BLC
Flickerless
Input / Output Connector
Power Consumption
(Option : AC 24V/DC 12V)
Dome Size (Ø)
Weight
NTSC PAL
NTSC : 525 Lines PAL : 625 Lines
2 : 1 Interlace
15.734kHz 15.625kHz
59.94Hz 50Hz
1/3 inch SONY IT CCD
410K/380K [Normal:270K/250K] 470K/440K[Normal:320K/290K]
More than 48dB (AGC Off)
550 TV Lines [High: 480 TV Lines / Normal: 380 TV Lines]
1.0 Vp-p (75 Ohms, composite)
Fixed Lens (f=2.45mm, 3.8mm, 6mm Selectable)/ Vari-focal Lens
Manual
Internal
0.3 Lux(High/Normal)/ 0.1 Lux(Day&Night)/ 0 Lux(IR LED)
1/60 ~ 100,000 Sec. 1 /50 ~ 100,000 Sec.
Auto
Auto, On / Off (Option)
On / Off (with Slide Switch)
On / Off (with Slide Switch)
Power, Video, UTP (Option)
DC 12V (DC 9V~15V) / 3W (Max)
AC 24V (20V~28V) or DC 12V (10V~15V), 5W (Max)
100mm
Approx. 1210g
You must be fully aware of all the distinctive
features and precautions related to this
camera before installing it.
Built-in camera
bracket will make user
much easier to rotate in
any direction.
3-axis
360º
360º
90º
NAME AND FUNCTION:
Fixed Lens Type
CAMERA SET-UP:
Vari-focal Lens Type
Vari-focal Lens Type
The image does not
appear on the screen.
Check the power source for the monitor and camera
and assure that the voltage and polarity are properly
connected and being supplied correctly.
The image on the
screen is dim.
Check if the lens is stained. If dirty, clean the lens with
a soft, clean cloth.
Adjust the Back Focus of the lens again.
The camera does not work
properly, the surface of the
camera case is hot, and a black
line appears on the screen.
Check if you have connected the camera to a proper
power source and If there is no problem with the power,
turn the unit off immediately and seek assistance from
our After Service department.
The screen blinks a lot. Check if the camera is pointed toward the sun or a
fluorescent lamp.
Adjust the angle or location of the camera if too much
light is coming into the screen.
TROUBLESHOOTING:
If you have trouble operating your camera, refer to the following.
If the guidelines do not enable you to solve the problem, contact an authorized technician.
1
2
3
4
5
2
1
3
P /N
:3
8 1
0 -0
0
6 2 D
ve
r.
0 6 1 2 E
! Do not install the camera in
extreme temperature conditions.
Do use the camera under conditions where
temperatures are within -10°C to 45°C.
Be especially careful with ventilation
under high temperatures.
! Do not install or use the camera
in an environment where the
humidity is high.
It can cause the image quality to be poor.
! Do not drop the camera or
subject them to physical shocks.
It can cause malfunctions to occur.
! Do not disassemble the camera.
There are no user-serviceable parts
inside it.
! Note
When this camera is installed near
wireless communication devices
that emits strong electromagnetic
field, irregularity such as noise on
the monitor may appear.
PRECAUTIONS:
46
.0
83.5
76
.0
76.0
4-Ø 4.5
139.5
38
.0
100.0
80.0
11 1. 0
38 .5
24
.5
※ 1/2 JIS B0202-1982
※ 3/4 JIS B0202-1982
INSTALLATION:
Draw out power / video wires
to the connecting places.
4
Fix the surface mount bracket
by screws on the ceiling.
3
Stick the guide pattern on the
wall or ceiling.
1
Adjust desired focus and scene
by turning and moving the
3-axis camera bracket by hand.
6
Drill four holes according to
the guide pattern then insert
anchors into the drilled holes.
2
Put the dome cover over the
base.
7
Fix the dome cover on the base
by L-Wrench.
8
Connect the dome base to the
surface mount bracket by screws.
5
Ceiling
Guide Pattern
Surface Mount
Bracket
Surface Mount
Screw
Tapping Screw
Dome Base
Dome Cover
L-Wrench
Owner's Manual
Guide Pattern Service Monitor Cable
L-Wrench
Surface Mount Bracket
Tapping Screw
Surface Mount Screw
Camera Lay-out
Tilt rotation: Adjusting the vertical angle.
Pan rotation: Adjusting the horizontal angle.
Horizontal rotation: Adjusting the horizontal
position of the screen. Focus handle: Focus (Far or Near)
Zoom handle: Zoom (Tele or Wide) 1
2
3 4
5
CAUTION : In case of AGC off,
the switching of D&N doesn't work.
Because the D&N switching function
is related in AGC level.
DC Level Adjustment V.R a
Function Selection Switch:
•FL(Flickerless) ON/OFF
•AGC(Auto Gain Control) ON/OFF
•BLC(Back Light Compensation)
ON/OFF
Service Monitor Connecter:
Use service monitor connector
to set camera angle & focus
when installing.
b
c
BLC
AGC
FL
ON
OFF ON
DC
L EV EL
VI DE O
SW
IT CH ON 3
1
2
WIDE
TELE
AC 24V J503
J504
AC24V J5 01
J5 02
HE AT ER
/A UD IO
J5 05
a
b
c
CONNECTION:
• The wire is non-polarized.
• Use AC 24V power source or DC 12V power source.
No.
#1
#2
Function
Video Output
Power Input
Remark
1.0 Vp-p
AC24V(20V~28V)orDC12V(11V~15V), Max 5W/420mA
Terminal Color
Yellow
Green
#1
#2
Video
(Yellow)
Power - AC 24V/ DC 12V
(Green)
Video Output
GND
AC 24V/DC 12V Power Type
• The wire is polarized.
• Use DC 12V power source.
#1
#2
No.
#1
#2
Function
Video Output
Power Input
Remark
1.0 Vp-p
DC 12V(DC9V~15V), Max 3W/ 250mA
Terminal Color
Yellow
Red
Video
(Yellow)
Power - DC 12V
(Red)
Video Output
GND
DC 12V Power Type
Connecting to Monitor and Power
• Power Consumption: 5W
• IR LED Specification: 850nm / 30° (24EA)
IR LED (3.8mm Fixed Lens Only) : Option
HEATER: Option
• Power Consumption: 10W
• Operating Temperature Range: -40°C ~ 50°C