CNB GM3005PDNF - Manual

Digital Color Camera Series COLOR VIDEO CAMERA
Color CCD
COLOR VIDEO CAMERA
Color CCD
Digital
P/N : 3810-0018H (Ver.0511)
PRINTED IN KOREA Color Video Camera Series
Design and specifications are subject to
change without notice.
OWNER'S MANUAL
DIGITAL CAMERA SERIES
COLOR VIDEO CAMERA
4
2
5
6 7
8 9
10 11
12 13
3 14 15
16 17
19 18
21 20
23 22
1. SAFETY INSTRUCTIONS
2. PRECAUTIONS
3. FEATURES
4. NAME AND FUNCTIONS
5
6
7
8
9
10
11
5. INSTALLATION (LENS)
6. COMPOSITION
7. CONNECTIONS
8. SPECIFICATIONS
.............
............................
..................................
.............
......................
............
................
12
13
14
15
16
17
18
18
20
................
..........................
..................
...........................
..........................
...........................
.......................
.....................
...........
FL (Flickerless)
If the camera is used with 50Hz fluorescent lighting, there maybe flicker on the
screen. In this case, FL switch should be set to ON position. But, FL switch
should be set to OFF in 60Hz power source. Flickerless mode can overcome
flickering on the screen in case that the AC power frequency is different from
the vertical sync frequency of the camera.
AGC (Automatic Gain Control)
With AGC ON, the setting, camera's sensitivity is automatically increased when
the level of ambient light drops. AGC function automatically controlls signal gain
in the range of maximum 28dB.
BLC (Back Light Compensation)
Strong light entering from an object's background may cause the lens iris to close,
there by possibly obscuring or darkening desired portions of the scene.
Back Light Compensation function automatically adjust the video level so as to
preserve visibillity in important section of the scene.
Read Instructions
Read all of the safety and operating instructions
before using the product.
High Sensitivity 1/3 Inch Super HAD CCD Pick-up.
Min lllumination : 0.1 Lux Normal Resolution
0.3 / 0.5 Lux High Resolution
Auto/Manual Iris lens Selectable.
AGC (Automatic Gain Control)
BLC (Back Light Compensation) on/off
Flickerless ON/OFF
High Resolution : Horizontal 550 / 480 TV Lines High Resolution
380 TV Lines Normal Resolution
Installation
Do not place this product on an unstable cart, stand,
or table. The product may fall causing serious injury
to a child or adult, and damage to the product.
Use only with a cart or stand recommended by the
manufacturer, or sold with the product.
Mounting should follow the manufacturer's instructions,
and should use a mounting accessory recommended
by manufacturer.
Power source
This product should be operated only from the type
of power source indicated on the marking label.
If you are not sure of the type of power supplied to
your home, consult your dealer or local power
company.
Retain Instructions
Save this instructions for later use.
Cleaning
Unplug this appliance from wall outlet before
cleaning. Do not use liquid cleaners or aerosol
cleaners. Use a damp cloth for cleaning.
Water and Moisture.
Do not use this product near water or moisture.
(For example. near a bathtub, wash bowl, kitchen
sink, or laundry tub, in a wet basement, or near a
swimming pool,etc)
Handling
⑤ Tripod Mounting base
Mounting base for installing the camera.
④ C-Mount Lens Adapter
Used to attach C-mount lens. (See page 13)
③ Lens Mount Cap
Be sure to cap the lens
mount when the lens is not mounted.
ON
ON
OFF ON
FL OFF AGC ON BLC OFF
OFF ON
FL OFF
ON
FL OFF
AGC ON BLC OFF
OFF ON
AGC ON BLC OFF
Side-view Rear-view
CAUTION! TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN
Explanation of two Symbols
The lightning flash with arrowhead symbol, within an equilateral
triangle, is intended to alert the user to the presence of un-insulated
"dangerous voltage" within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to
alert the user to the presence of important operating and maintenance-
(servicing) instructions in the literature accompanying the appliance.
THE GRAPHIC SYMBOLS WITH SUPPLEMENTAL MARKING ARE ON THE BOTTOM OF THE SYSTEM.
"WARNING-TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THE UNIT TO RAIN OR MOISTURE"
INFORMATION
This equipment has been tested and found to comply with limits for a Class A digital device, pursuant to part 15
of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at their own expense.
WARNING
The manufacturer could void the user's authority to operate the equipment.
CAUTION - To prevent electric shock and risk of fire hazards:
Do NOT use power sources except for that specified.
Do NOT expose this appliance to rain or moisture.
This installation should be made by a qualified service person and should abide to all local codes.
Before using this camera, please read this operation manual carefully to obtain
the best result and keep this manual for future reference.
Thank you for purchasing this COLOR VIDEO CAMERA.
. Mode Setting Dip Switch
. Lens Connector
. Back-focus Adjustment
. Mounting a Lens
. AC 24V / DC 12V Input Model
. DC 12V Input Model
. AC 24V / DC 12V Input Model
. DC 12V Input Model
Do not disassemble the camera and never touch
parts inside the camera.
Be sure the ambient temperature is less than
40℃ in installation intended for long term
continuous operation.
Avoid installing in a humid or dusty place.
Avoid installing in places where there are
strong magnetic fields and electric signals.
Avoid installing in places where the camera
would be subject to strong vibrations.
Never expose the camera to rain and water.
Installation and storage
Do not point the camera at the sun. This could
damage the camera whether it is operating or not.
Do not install the camera where the temperature
could exceed the allowable range.
Do not drop the camera or subject it to shocks
and vibrations to avoid possible damage.
When attaching or removing the lens, handle
with care in order to that moisture and dust do
not enter the camera.
DC 12V
DC VIDEO
ELC
AGC ON
OFF ON ON
FL OFF BLC OFF VIDEO OUT
Class 2 Only
DC LEVEL 1
2
3
4
IRIS
④ DC Level Control Volume
(See page 12)
⑤ Lens Connector
(See page 17)
⑥ Video Output Connector
(BNC-Type)
① Lens Select Switch
② Mode Setting
Dip Switch
(See page 11)
③ Power Input
Terminal
Rear-view
DC VIDEO
ELC
AGC ON
OFF ON ON
FL OFF BLC OFF
AC 24V / DC 12V
VIDEO OUT
Class 2 Only
LINE LOCK
DC LEVEL 1
2
3
4
IRIS
④ DC Level Control Volume
(See page 12)
⑤ Lens Connector
(See page 17)
⑥ Video Output Connector
(BNC-Type)
① Lens Select Switch
② Mode Setting
Dip Switch
(See page 11)
③ Power Input
Terminal
② Back-Focus Screw (See page 14) ① CS-Mount Lens Adapter
Mount for installing the lens.
Signal system
CCD Pick-up Element
Effective Pixels
Video Output
Sync. System
Luminance S/N Ratio
Horizontal Resolution
Sensitivity
Lens Mount
Electronic Shutter NTSC PAL NTSC PAL
2:1 Interlace Transfer 1/3 Inch Super HAD CCD
768(H) x 494(V) 752(H) x 582(V) 510(H) x 492(V) 500(H) x 582(V)
Composite: 1.0V p-p, 75Ω, Unbalanced
Internal Sync
More than 48dB (AGC OFF)
550 / 480 TV Lines 380 TV Lines
0.3 / 0.5Lux(F1.4, 30IRE, AGC ON) 0.1Lux(F1.4, 30IRE, AGC ON)
C/CS Mount
1/60 ~1/100,000 (NTSC), 1/50 ~1/100,000(PAL)
Normal Resolution High Resolution White Balance
Auto Gain Control
Back Light Compensation
Flickerless
Applicable Lens
Supply Voltage
Power Consumption
Operating Temperature
Storage Temperature
External Dimensions
Weight AWB
On/Off Selectable(20dB) On/Off Selectable(28dB)
On/Off Selectable
On/Off Selectable
DC Iris / Video Iris / Manual Lens
DC 12V(10V~15V)
180mA / 2.2W (Max) 140mA 1.7W (Max)
-10℃~+50℃(Recommendation:-5℃~+40℃)
-20℃~+60℃
[Long Body] 63.6x54x129.7mm [Middle Body] 63.6x54x94.1mm
[Long Body] 390g [Middle Body] 335g
Signal system
CCD Pick-up Element
Effective Pixels
Video Output
Sync. System
Luminance S/N Ratio
Horizontal Resolution
Sensitivity
Lens Mount
Electronic Shutter NTSC PAL NTSC PAL
2:1 Interlace Transfer 1/3 Inch Super HAD CCD
768(H) x 494(V) 752(H) x 582(V) 510(H) x 492(V) 500(H) x 582(V)
Composite: 1.0V p-p, 75Ω, Unbalanced
Internal Sync
More than 48dB (AGC OFF)
550 / 480 TV Lines 380 TV Lines
0.3 / 0.5Lux(F1.4, 30IRE, AGC ON) 0.1Lux(F1.4, 30IRE, AGC ON)
C/CS Mount
1/60 ~1/100,000 (NTSC), 1/50 ~1/100,000(PAL)
Normal Resolution High Resolution MODEL
MODEL
White Balance
Auto Gain Control
Back Light Compensation
Flickerless
Applicable Lens
Supply Voltage
Power Consumption
Operating Temperature
Storage Temperature
External Dimensions
Weight AWB
On/Off Selectable(20dB) On/Off Selectable(28dB)
On/Off Selectable
On/Off Selectable
DC Iris / Video Iris / Manual Lens
AC 24V(20V~28V) or DC 12V(10V~15V)
330mA / 4W (Max) 240mA 2.8W (Max)
-10℃~+50℃(Recommendation:-5℃~+40℃)
-20℃~+60℃
[Long Body] 63.6x54x129.7mm [Middle Body] 63.6x54x94.1mm
[Long Body] 390g [Middle Body] 335g
. User Information
. Contents
2. PRECAUTIONS
4. NAME AND FUNCTIONS
1. SAFETY INSTRUCTIONS
Please insert a lens cable when using the DC iris lens or
Video iris lens.
Lens select switch on the rear pannel should be set to ELC
position when using the manual lens.
When using the VIDEO type lens, please adjust a brightness
of image with volume attached with the lens.
When using the DC type lens, please adjust a
brightness of image by DC level volume
on the rear panel.
- Turn toward L (left) to make the picture brighter.
- Turn toward R (right) to make the picture darker.
DC 12V
DC VIDEO ELC
AGC ON
OFF ON ON
FL OFF BLC OFF VIDEO OUT
Class 2 Only
DC LEVEL 1 2 3 4
IRIS
5. INSTALLATION (LENS)
Video Type lens : Set lens Switch to Video. Connect the lens cable of a video Type lens.
If the plug on the cable is a different type, replace it with the provided 4-pin iris plug.
DC type lens : Set lens switch to DC. Connect the lens cable of a DC(Galvanometric) type lens.
If the plug on the cable is a different type, replace it with the provided 4-pin iris plug.
Pin Assignment :
#1 #3
#2 #4
Pin No.
#1
#2
#3
#4
Signal
+12V DC
N.C
Video(0.7Vp-p, high impedance, no sync)
GND
VIDEO Iris Type Lens
Pin No.
#1
#2
#3
#4
Signal
Damping coil (-)
Damping coil (+)
Drive coil (+)
Drive coil (-)
DC Iris Type Lens
When using an auto-iris lens, install the accessory lens plug
on the lens cable as follows.
NOTE After installing the connector plug, connect it to
the lens connector on the rear panel of camera.
1
1
1
1
1
............................
......................................................
......................................................
......................................................
......................................................
. Lens Connector Plug (E-4-191J-100)
. Lens Mount Cap
. C-mount Adapter
. L-Wrench
. Owner's Manual
!
Design and specifications are subject to change without notice.
This color video camera is designed to output video signals conforming
to the NTSC(PAL) standard. So that it cannot be used with video recorder
or color monitors which use color systems other than NTSC(PAL)
The lens mount cap and C-mount adapter are attached when supplied.
6. COMPOSITION
DC 12V
DC VIDEO ELC
AGC ON
OFF ON ON
FL OFF BLC OFF VIDEO OUT
Class 2 Only
DC LEVEL 1
2
3
4
IRIS
Connect the video output of the camera to the video input of a monitor
or other equipment. When using a "loop through" connection of two or
more monitors, set the 75Ω switch of only the final monitor to on.
Determine the type of cable according to the
distance of the connected equipment.
DC 12V
Power Source
NOTE
Do not turn any component's power
on until all connections are completed.
To Power input terminal
To Video input connector
To Lens connector
Video-Iris Lens
(or galvanometric-Iris Lens)
7 . CONNECTIONS
8. SPECIFICATIONS 3. FEATURES
DC 12V Input Model
DC 12V Input Model
8. SPECIFICATIONS AC 24V / DC 12V Input Model
. Memo Mode Setting Dip Switch AC 24V / DC 12V Input Model
WITH A ZOOM LENS
1) Fully open the aperture and set the lens to the maximum tele-photo position. Then turn the focus ring to focus.
In the case of an auto-iris lens only, shoot a comparatively dark object so that the aperture is fully open.
2) Set the lens to its maximum wide-angle position.
3) Loosen the two back-focus screws with a L-wrench, and turn the lens mount to focus.
4) After adjusting the back-focus, tighten the back-focus screw.
5) Repeat step 1)~3) until the difference between focusing position 1) and 2)becomes smallest.
CAUTION : Do not forcibly turn back-focus screw, it could cause damage to the camera.
When a lens is mounted, adjustment of the back-focus may sometimes be required.
Adjust the lens focus ring when the correct focus cannot be obtained.
WITH A FIXED-FOCUS LENS
1) Fully open the aperture and set the focus ring to "∞"(infinity).
In the case of an auto-iris lens only, shoot a comparatively dark
object so that the aperture is fully open.
2) Loosen the two back-focus screws with a L-wrench, and turn the lens mount to focus.
3) After adjusting the back-focus, tighten the back-focus screw.
Back-focus Adjustment
1 Remove the lens mount cap from the camera.
2 Attach or remove the C-mount adapter depending on the lens to be used.
3 Attach the lens to the lens mount. Secure it so that it does not become loose.
5 When installing a fixed lens, lens select switch should be set to ELC position.
4 If the lens has an auto-iris mechanism, connect the lens cable to the lens connector.
-When installing a video-iris lens, lens switch should be set to VIDEO position.
-When installing a galvanometric-iris lens, lens switch should be set to DC position.
1) Set AGC mode to off.
2) When using a video type lens: Adjust the level
control on the lens to produce minimum smear
and optimum pictures.
3) When using a DC type lens: Adjust the video
level control on the main menu to produce
minimum smear and optimum pictures.
4) Set AGC mode to on. It is recommended that
the AGC be used in the "on" mode after adjusting
the video level.
-If the adapter is attached so tightly that it is difficult to remove it. (Keep the C-mount adapter for possible future use.)
ADJUSTING AUTO-IRIS LENSES
L-Wrench
Mounting a Lens
Lens Connector