CNB GS3010PBX User Manual

B/w ccd, Owner's manual, Cctv video camera

Advertising

B/W Box Camera Series

P/N : 3810-0113A

(Ver.0703E)

B/W Box Camera Series

Design and specifications are subject to
change without notice.

B/W

•A

CCTV VIDEO CAMERA

B/W CCD

CCTV VIDEO CAMERA

B/W CCD

monochrome

OWNER'S MANUAL

B/W BOX CAMERA SERIES

CCTV VIDEO CAMERA

INFORMATION
This equipment has been tested and found to comply with limits for a Class A digital device, pursuant to part 15
of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at their own expense.

WARNING

The manufacturer could void the user's authority to operate the equipment.

CAUTION - To prevent electric shock and risk of fire hazards:

Do NOT use power sources except for that specified.
Do NOT expose this appliance to rain or moisture.

This installation should be made by a qualified service person and should abide to all local codes.

CAUTION! TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

Explanation of two Symbols

The lightning flash with arrowhead symbol, within an equilateral

triangle, is intended to alert the user to the presence of un-insulated

"dangerous voltage" within the product's enclosure that may be of

sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to

alert the user to the presence of important operating and maintenance-

(servicing) instructions in the literature accompanying the appliance.

THE GRAPHIC SYMBOLS WITH SUPPLEMENTAL MARKING ARE ON THE BOTTOM OF THE SYSTEM.

"WARNING-TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THE UNIT TO RAIN OR MOISTURE"

. User Information

Handling

Do not disassemble the camera and never touch
parts inside the camera.

Be sure the ambient temperature is less than
40℃ in installation intended for long term
continuous operation.

Avoid installing in a humid or dusty place.

Avoid installing in places where there are
strong magnetic fields and electric signals.

Avoid installing in places where the camera
would be subject to strong vibrations.

Never expose the camera to rain and water.

Installation and storage

Do not point the camera at the sun. This could
damage the camera whether it is operating or not.

Do not install the camera where the temperature
could exceed the allowable range.

Do not drop the camera or subject it to shocks
and vibrations to avoid possible damage.

When attaching or removing the lens, handle
with care in order to that moisture and dust do
not enter the camera.

2. PRECAUTIONS

Read Instructions

Read all of the safety and operating instructions
before using the product.

Installation

Do not place this product on an unstable cart, stand,
or table. The product may fall causing serious injury
to a child or adult, and damage to the product.
Use only with a cart or stand recommended by the
manufacturer, or sold with the product.
Mounting should follow the manufacturer's instructions,
and should use a mounting accessory recommended
by manufacturer.

Power source

This product should be operated only from the type
of power source indicated on the marking label.
If you are not sure of the type of power supplied to
your home, consult your dealer or local power
company.

Retain Instructions

Save this instructions for later use.

Cleaning

Unplug this appliance from wall outlet before
cleaning. Do not use liquid cleaners or aerosol
cleaners. Use a damp cloth for cleaning.

Water and Moisture.

Do not use this product near water or moisture.
(For example. near a bathtub, wash bowl, kitchen
sink, or laundry tub, in a wet basement, or near a
swimming pool,etc)

1. SAFETY INSTRUCTIONS

DC 12V

Class 2 Only

VIDEO OUT

LEVEL

OFF

EI
FL
AI

OFF

BLC

S1 S2

VIDEO

AGC

Connect the video output of the camera to the video input of a monitor or other equipment.
When using a "loop through" connection of two or more monitors, set the 75Ω switch of only the final
monitor to on. Determine the type of cable according to the distance of the connected equipment.

DC 12V

Power Source

NOTE

Do not turn any component's power

on until all connections are completed.

To Power input terminal

To Video input connector

7. CONNECTIONS

Video Type lens :

Set lens Switch to Video. Connect the lens cable of a video Type lens.

If the plug on the cable is a different type, replace it with the provided 4-pin iris plug.

DC type lens :

Set lens switch to DC. Connect the lens cable of a DC(Galvanometric) type lens.

If the plug on the cable is a different type, replace it with the provided 4-pin iris plug.

Pin Assignment :

Pin No.

#1
#2
#3
#4

Signal

+9V DC

N.C

Video(1.0Vp-p, high impedance, no sync)

GND

VIDEO Iris Type Lens

Pin No.

#1
#2
#3
#4

Signal
Damping coil (-)
Damping coil (+)
Drive coil (+)
Drive coil (-)

DC Iris Type Lens

When using an auto-iris lens, install the accessory lens plug
on the lens cable as follows.

NOTE

After installing the connector plug, connect it to

the lens connector on the rear panel of camera.

Lens Connector

4. NAME AND FUNCTIONS

Holder Screw Hole

Used to install the camera on an optional

holder.(Tripod or Bracket)

The optional holder must be equipped with

the screw specified as shown right.

CS-Mount Holding Screw

Used to readjust back focus of the camera.

There are two back focus lock screws.

These must be loosened before the camera

may be back focused.

Loosen the lock screws to turn the CS-mount

lens adaptor, and tighten the lock

screws after adjustment.

Auto Iris Lens Connector

Used to connect Auto Iris Lens plug.

C-Mount Lens Adapter

Used to attach C-mount lens.

CS-Mount Lens Adapter

Used to attach CS-mount lens.

1/4"- 20 UNC (20 THREAD)

L : 4.5mm±0.2mm (ISO standard),

or 0.197" (ASA standard)

. Memo

High Sensitivity 1/3 Inch Super HAD CCD Pick-up.

Min lllumination : 0.001 Lux (Normal Resolution)

0.003 Lux (High Resolution)

Auto/Manual Iris lens Selectable.

AGC (Automatic Gain Control) LOW/HIGH

BLC (Back Light Compensation) ON/OFF

Flickerless ON/OFF

High Resolution : Horizontal 580 TV Lines High Resolution

380 TV Lines Normal Resolution

3. FEATURES

Rear-view

DC 12V Input Model

DC 12V

Class 2 Only

VIDEO OUT

LEVEL

OFF

EI
FL
AI

OFF

BLC

S1 S2

VIDEO

AGC

③ Mode Setting

DIP Switch

(See page 11)

⑥ Video Output Connector

(BNC-Type)

⑤ DC Level Control

Volume

② AGC Select Switch

① Lens Select

Switch

④ Power Input

Terminal

AC 24V / DC 12V Input Model

AC 24V

DC 12V

Class 2 Only

VIDEO OUT

LEVEL

OFF

EI
FL
AI

OFF

BLC

S1 S2

VIDEO

AGC

Rear-view

③ Mode Setting

DIP Switch

(See page 11)

⑥ Video Output Connector

(BNC-Type)

⑤ DC Level Control

Volume

② AGC Select Switch

① Lens Select

Switch

④ Power Input

Terminal

BLC (Back Light Compensation)

Strong light entering from an object's background may cause the lens iris to close,

there by possibly obscuring or darkening desired portions of the scene.

Back Light Compensation function automatically adjust the video level so as to

preserve visibillity in important section of the scene.

EI (Electronic Iris)

Electronic iris shutter is automatically controlled at the speed of

1/60 ~ 100,000 sec (EIA Mode), 1/50 ~ 100,000 sec (CCIR Mode).

Select this mode when using the manual lens.

AI (Automatic Iris)

Electronic iris shutter is fixed 1/60 sec (EIA Mode), 1/50 sec (CCIR Mode).

Select this mode when using the DC or video iris vari-focal lens.

FL (Flickerless)

If the camera is used with 50Hz fluorescent lighting, there maybe flicker on the

screen. In this case, FL switch should be set to ON position. But, FL switch

should be set to OFF in 60Hz power source. Flickerless mode can overcome

flickering on the screen in case that the AC power frequency is different from

the vertical sync frequency of the camera.

EIA (1/100), CCIR (1/120)

OFF ON

BLC

OFF

Mode Setting DIP Switch

OFF ON

BLC

OFF

OFF ON

BLC

OFF

OFF ON

BLC

OFF

Please insert a lens cable when using the DC iris lens or
Video iris lens.

Lens select switch on the rear pannel should be set to
DC or VIDEO position when using
the AUTO iris lens.

When using the VIDEO type lens, please adjust a brightness
of image with volume attached with the lens.

When using the DC type lens, please
adjust a brightness of image by setup
menu on the rear panel.

5. INSTALLATION

(LENS)

WITH A ZOOM LENS

1) Fully open the aperture and set the lens to the maximum tele-photo position. Then turn the focus ring to focus.
In the case of an auto-iris lens only, shoot a comparatively dark object so that the aperture is fully open.
2) Set the lens to its maximum wide-angle position.
3) Loosen the two back-focus screws with a L-wrench, and turn the lens mount to focus.
4) After adjusting the back-focus, tighten the back-focus screw.
5) Repeat step 1)~3) until the difference between focusing position 1) and 2)becomes smallest.

CAUTION : Do not forcibly turn back-focus screw, it could cause damage to the camera.

When a lens is mounted, adjustment of the back-focus may sometimes be required.
Adjust the lens focus ring when the correct focus cannot be obtained.

WITH A FIXED-FOCUS LENS

1) Fully open the aperture and set the focus ring to "∞"(infinity).
In the case of an auto-iris lens only, shoot a comparatively dark object so that the aperture is fully open.
2) Loosen the two back-focus screws with a L-wrench, and turn the lens mount to focus.
3) After adjusting the back-focus, tighten the back-focus screw.

Back-focus Adjustment

Signal system

CCD Pick-up Element

Effective Pixels

Video Output

Sync. System

Luminance S/N Ratio

Horizontal Resolution

Sensitivity

EIA CCIR EIA CCIR

2:1 Interlace Transfer 1/3 Inch Super HAD CCD

768(H) x 494(V) 752(H) x 582(V) 510(H) x 492(V) 500(H) x 582(V)

1.0V p-p, 75Ω

Internal Sync

More than 46dB (AGC OFF)

580 TV Lines 380 TV Lines

0.03 Lux(F1.2, 20IRE, AGC LOW) 0.01 Lux(F1.2, 20IRE, AGC LOW)

0.003 Lux(F1.2, 20IRE, AGC HIGH) 0.001 Lux(F1.2, 20IRE, AGC HIGH)

Normal Resolution

High Resolution

MODEL

8. SPECIFICATIONS

Lens Mount

Electronic Shutter

Auto Gain Control

Back Light Compensation

Flickerless

Applicable Lens

Supply Voltage

Power Consumption

Operating Temperature

Storage Temperature

C/CS Mount

1/60 ~1/100,000 (EIA), 1/50 ~1/100,000(CCIR)

LOW / HIGH Selectable

ON / OFF Selectable

DC Iris / Video Iris / Manual Lens

DC 12V (10V~15V)

100mA / 1.4W (Max)

-10℃~+50℃(Recommendation: -5℃~+40℃)

-20℃~+60℃

DC 12V Input Model

Signal system

CCD Pick-up Element

Effective Pixels

Video Output

Sync. System

Luminance S/N Ratio

Horizontal Resolution

Sensitivity

EIA CCIR EIA CCIR

2:1 Interlace Transfer 1/3 Inch Super HAD CCD

768(H) x 494(V) 752(H) x 582(V) 510(H) x 492(V) 500(H) x 582(V)

1.0V p-p, 75Ω

Internal Sync

More than 46dB (AGC OFF)

580 TV Lines 380 TV Lines

0.03 Lux(F1.2, 20IRE, AGC LOW) 0.01 Lux(F1.2, 20IRE, AGC LOW)

0.003 Lux(F1.2, 20IRE, AGC HIGH) 0.001 Lux(F1.2, 20IRE, AGC HIGH)

Normal Resolution

High Resolution

MODEL

8. SPECIFICATIONS

Lens Mount
Electronic Shutter
Auto Gain Control
Back Light Compensation
Flickerless
Applicable Lens
Supply Voltage
Power Consumption
Operating Temperature
Storage Temperature

C/CS Mount

1/60 ~1/100,000 (EIA), 1/50 ~1/100,000(CCIR)

LOW / HIGH Selectable

ON / OFF Selectable

DC Iris / Video Iris / Manual Lens

AC 24V(20V~28V) or DC 12V(10V~15V)

330mA / 4W (Max) 240mA 2.8W (Max)

-10℃~+50℃(Recommendation: -5℃~+40℃)

-20℃~+60℃

AC 24V / DC 12V Input Model

1. SAFETY INSTRUCTIONS

2. PRECAUTIONS

3. FEATURES

4. NAME AND FUNCTIONS

5. INSTALLATION (LENS)

6. COMPOSITION

7. CONNECTIONS

8. SPECIFICATIONS

.............

............................

..................................

.............

......................

............

................

..........................

..................

...........................

..........................

...........................

.......................

.....................

...........

Before using this camera, please read this operation manual carefully to obtain
the best result and keep this manual for future reference.

Thank you for purchasing this CCTV VIDEO CAMERA.

. Mode Setting DIP Switch

. Lens Connector

. Back-focus Adjustment

. Mounting a Lens

. AC 24V / DC 12V Input Model

. DC 12V Input Model

. AC 24V / DC 12V Input Model

. DC 12V Input Model

. Contents

............................

......................................................

. Lens Connector Plug

(E-4-191J-100)

. Lens Mount Cap

. C-mount Adapter

. Owner's Manual

6. COMPOSITION

Design and specifications are subject to change without notice.

This B/W video camera is designed to output video signals conforming
to the EIA(CCIR) standard. So that it cannot be used with video recorder
or B/W monitors which use B/W systems other than EIA(CCIR)

The lens mount cap and C-mount adapter are attached when supplied.

Mounting a Lens

Remove the lens mount cap from the camera.

Attach or remove the C-mount adapter depending on the lens to be used.

Attach the lens to the lens mount. Secure it so that it does not become loose.

When installing a manual lens, mode setting DIP switch should be set to EI position.

If the lens has an auto-iris mechanism, connect the lens cable to the lens connector.

-When installing a video-iris lens, lens switch should be set to VIDEO position.

-When installing a galvanometric-iris lens, lens switch should be set to DC position.

-If the adapter is attached so tightly that it is difficult to remove it.

(Keep the C-mount adapter for possible future use.)

Advertising

This manual is related to the following products:

GS3010NBX

Popular Brands

Popular manuals