Codelocks Slam Latch for KitLock - Manual (Page 2)

Optional
strike plate
Cutting points
Slam Latch can be fitted
for left or right closing
6. Fix the KitLock to the door, passing the panhead bolt
(5) through the top hole and the countersunk bolt (6)
through the bottom hole of the mounting plate. Ensure the
spindle (7) passes through the centre of the spindle hole
in the mounting plate.
7. Fit the Slam Latch (3) to the mounting plate using the four
fixing bolts (10). Enter your master or user code and turn the
handle to retract the latch. Release the handle and make sure
the latch springs back.
8. If required, strike plate (4) can be mounted on door frame to
receive the latch. Fit accurately ensuring that the latch enters
the strike aperture easily. If required packing pieces (2) can be
used to align the latch with the strike.
1. Remove the mounting plate (1) from the Slam Latch (3) by
removing the 4 fixing bolts (10).
2. Using the mounting plate as a template for the latch position,
place on the inside face of the door as dictated by the door frame
surrounding. Mark spindle hole and top and bottom fixing holes.
Please note there are two positions for the lower fixing hole; the
upper being used for the KL1500 and the lower for the KL1200.
When choosing the position of your Slam Latch, take into account
any rebate or frame that the door closes against. The Slam Latch
should be positioned between 2mm (
5 / 64 ”) and 4mm ( 5 / 32 ”) back
from the edge of the door or rebate, or any striking plate mounted
to the door frame or rebate.
3. Drill the 13mm (½”) spindle fixing hole and the two 6mm (¼”) holes.
Before installation familiarise yourself with the operation
and programming of the KitLock being fitted to the
Slam Latch and check the Slam Latch box contents.
Special Notes
Slam Latch fitting instructions
4. Cut pan head bolt for upper fixing hole and countersunk bolt for
lower fixing hole. Length of bolts should be the thickness of the
door plus 10mm (
3 /
8
”), or 1 to 2 break off sections. Cut the bolts
at one of the cutting points to avoid damaging the thread. Use
pliers cutting jaws to crimp around the cutting point several
times. The surplus should now easily break off.
5. Choose the spindle to suit your door thickness. For doors 3mm
( 1 / 8 ”) to 18mm ( 3 / 4 ”), use the shorter 30mm (1 1 / 8 ”) spindle, for
doors 18mm ( 3 / 4 ”) to 28mm (1 1 / 16 ”) use the longer 40mm (1½”)
spindle. Screw the spindle with the 9mm ( 3 / 8 ”) end into the
socket in the KitLock using the countersunk fixing bolt (6).
Cut one section off the bolt if using a shorter spindle.
Packing pieces (optional)
Fitting instructions WITHOUT mounting plate
1. As previous.
2. As previous step 2. But also mark around outside edge of
square section of mounting plate.
3. As previous.
4. Using the guide marks made using the mounting plate template
place one of the packing pieces on the inside of the door and
mark the 4 corner fixing holes.
5. Fit the KitLock to the door using two panhead bolts (5) and fit
the spindle to the KitLock with the countersunk fixing bolt (6).
If not countersinking the bottom fixing bolt, use one of the
packing pieces to allow clearance.
6. Place the Slam Latch (3) over the spindle and secure with the
four screws (8) provided. Enter your master or user code and
turn the handle to retract the latch. Release the handle and
make sure the latch springs back.
1
5
6
6 7
3
4
10
10
2
KL1500
KL1200
slam 6pp inst. artwork_Layout 1 04/03/2013 11:44 Page 4