A798 – diagnostics form – CognitiveTPG A798 User Manual

Page 2

Advertising

To enter Printer Config Menu :
1) Flip DIP switch #1 down
2) Reset the printer, while holding
the Paper Feed button down

Model number

: A798-720D-TD00

Serial number

: C073400014

Boot Firmware
Revision

: V3.02

CRC

: D554

P/N

: 189-7940505A

Flash Firmware
Revision

: V3.01

CRC

: 4FFF

P/N

: 189-7940497A

H/W parameters
Flash Memory Size

: 2 Mbytes

Flash Logos/Fonts

: 64 kbytes

Flash User Storage

: 64 kbytes

Flash Perm’nt Fonts

: 0 kbytes

Flash Journal Size

: 1152 kbytes

SRAM Size

: 128 kbytes

Head setting

: C

Pre-Heating

: Disabled

Print Density

: 100%

Max Speed

: 150 mm/sec

Paper Width

: 80 mm

Max Power

: 55 W

Knife

: Enabled

Partial Cut

: 125 steps

Paper Low Sensor

: Disabled

Comm. Interface
RX Buffer Size

: 4096

Interface type

: RS232/USB

Parameters
Baud Rate

: 115200

Data Bits

: 8

Stop Bit

: 1

Parity

: NONE

Flow Control

: DTR/DSR

Reception Errors

: Ignore

USB Driver Type

: Printer Class

USB Packet w/Error

: Reject

Resident Code Pages

: 437, 850, 852, 858

860, 863, 865, 866

1252, 862, 737, 857

1251, 1255, KZ-1048

Logo(s) defined

: NO

User Char(s) defined

: NO

Journal Unused

: 1152 kbytes

*** A798 – Diagnostics Form ***

When the printer is configured for USB, this

location will show either: “USB Driver Type:

Native”, “USB Driver Type: Printer Class”, or “USB

Driver: Comm Class”.

Print Test and Configuration Menu Sample.

Samples will vary depending on the printer model.

Configure the printer if necessary (page 20).

��

� ��

��

� ��

��

� ��

��

� ��

��

� ��

��

� ��

��

� ��

��

� ��

��

� ��

��

� ��

��

� ��

��

� ��

��

� �

��

� ��

��

� ��

��

� ��

��

� ��

��

� ��

��

� ��

��

� ��

��

� ��

��

� ��

��

� ��

��

� ��

��

� ��

��

� �

��

� �

��

� ��

��

� ��

��

� ��

��

� ��

��

�

��

�

��

� ��

��

� ��

��

� ��

��

�

��

DECLARATION OF CONFORMITY

Type of Equipment: Information Technology Equipment – Printer

Model: A798-XXXX-XXXX

Model: A799-XXXX-XXXX (X = any alphanumeric character)

Applicable EU Directives:

2004/108/EC (electromagnetic compatibility directive)

2006/95/EC (low voltage directive for product safety)

Harmonized Standards:

EN 55024 (1998/A1:2001/A2:2003) Information Technology Equipment Immunity Characteristics

EN 55022 (2006/A1:2007) EMC, Class B, Limits and Methods of Measurement of Interference

Characteristics of IT Equipment

IEC 60950-1 (2005) Second Edition - Product Safety Standard.

“CognitiveTPG, LLC., 950 Danby Road, Ithaca, New York, 14850, declares that the equipment specified

above conforms to the referenced EU Directives and Harmonized Standards.”

Date: November 28, 2012

Jeffrey C Phoenix, Regulatory Compliance Engineer, CognitiveTPG, LLC

Ref #: 189-1300058 Rev F

��

Run a diagnostic test (page 19).

��

��

��

Route cables as shown for your setup configuration (page 19).

Connect the power cable (page 18).

9-pin or 25 pin Serial or USB cable (serial: page 16; USB: page 17).

Cash drawer (if your installation includes this feature, page 15).

��

��

��

����

��

When using USB (step “b” below),

use caution to ensure the USB

cable is connected to the USB

connector on the back left of

the printer and not into the

cash drawer connector that is
on the back right of the printer.

Connect the following cables based on your configuration, using a-b below.

Choose a location for the printer.

Advertising

Popular Brands

Popular manuals