CognitiveTPG A799 - Manual (Page 2)

6
Configure the printer if necessary (page 20).
DECLARATION OF CONFORMITY
Type of Equipment: Information Technology Equipment – Printer
Model: A798-XXXX-XXXX
Model: A799-XXXX-XXXX (X = any alphanumeric character)
Applicable EU Directives:
2004/108/EC (electromagnetic compatibility directive)
2006/95/EC (low voltage directive for product safety)
Harmonized Standards:
EN 55024 (1998/A1:2001/A2:2003) Information Technology Equipment Immunity Characteristics
EN 55022 (2006/A1:2007) EMC, Class B, Limits and Methods of Measurement of Interference
Characteristics of IT Equipment
IEC 60950-1 (2005) Second Edition - Product Safety Standard.
“CognitiveTPG, LLC., 950 Danby Road, Ithaca, New York, 14850, declares that the equipment specified
above conforms to the referenced EU Directives and Harmonized Standards.”
Date: November 28, 2012
Jeffrey C Phoenix, Regulatory Compliance Engineer, CognitiveTPG, LLC Ref #: 189-1300058 Rev F
3
Choose a location for the printer.
4
Connect the following cables based on your configuration, using a-b below.
When using USB (step “b” below),
use caution to ensure the USB
cable is connected to the USB
connector on the back left of
the printer and not into the
cash drawer connector that is
on the right back of the printer.
���������
���������
�����
���
���������
���������������������
���������
�������������
��������
���������������
���������������
�����
������
���������
�����������
�����
�������������
����
������
���������
����
�����
�������������
�����������������
�������������������
a
Cash drawer (if your installation includes this feature, page 15).
b
9-pin or 25-pin serial or USB cable (serial: page 16; USB: page 17).
c
Connect the power cable (page 18).
d
Route cables as shown for your setup configuration (page 19).
���������
�����
��������
�������
������� ���
�����
������������
�������������
���������
�������������
�����������
�����
�������������
���������
���������������
���������������
�����������
�����������
���������������
�����
������
�����
���������
�����
���������
�������������
������������
�������������
���
�����
5
Run a diagnostic test (page 19).
- Set Firmware Features - > 8 clicks
*** A799 - Diagnostics Form ***
Model number : A799-120D-TD00
Serial number : 0000000000
Boot Firmware
Revision : V3.02
CRC : 7E22
P/N : 189-7940489B
Flash Firmware
Revision : V3.01
CRC : 4448
P/N : 189-7940490A
H/W parameters
Flash Memory Size : 4 Mbytes
Flash Logos/Fonts : 1024 kbytes
Flash User Storage : 960 kbytes
Flash Perm’nt Fonts : 960 kbytes
Flash Journal Size : 128 kbytes
SRAM Size : 512 kbytes
Head settting : D
Motor ID : 1
Paper Type Setting : Type 0, Monochrome
Color Density Adj : n/a
Print Density, Mono : 100%
Max Speed : 250 mm/sec
Paper Width : 80 mm
Max Power : 55 W
Knife : Enabled
Partial Cut : 125 steps
Paper Low Sensor : Enabled
No Paper Low Extension
Comm. Interface
RX Buffer Size : 4096
Interface Type : RS232/USB
Parameters
Baud Rate : 115200
Data Bits : 8
Stop Bit : 1
Parity : NONE
Flow Control : DTR/DSR
Reception Errors : Ignore
USB Driver Type : Printer Class
USB Packet w/Error : Reject
When the printer is configured for USB, this
location will show either: “USB Driver Type:
Native”, “USB Driver Type: Printer Class”, or “USB
Driver: Comm Class”.
Print Test and Configuration Menu Sample.
Samples will vary depending on the printer model.
The A799 is LogoEZ® compatible for ease of
setting-up your logo and two-color design needs.