CognitiveTPG A799II - Manual (Page 2)

6
Configure the printer if necessary (page 24).
DECLARATION OF CONFORMITY
Model: A798-XXXX-XXXX
Model: A799-XXXX-XXXX (X = any alphanumeric character)
CognitiveTPG, LLC, 950 Danby Road, Ithaca, New York, 14850
This declaration of conformity is issued under the sole responsibility of the Manufacturer: CognitiveTPG, LLC
Information Technology Equipment – Thermal Printer
The object of the declaration described above is in conformity with Directive 2011/65/EU of the European Parliament and
of the Council of 8 June 2011 on the restriction of the use of certain hazardous substances in electrical and electronic
equipment. With the exception of models A798-XXXP-XXXX and A799-XXXP-XXXX.
Applicable EU Directives:
2004/108/EC (electromagnetic compatibility directive)
2006/95/EC (low voltage directive for product safety)
Harmonized Standards:
EN 55024 (1998/A1:2001/A2:2003) Information Technology Equipment Immunity Characteristics
EN 55022 (2006/A1:2007) EMC, Class B, Limits and Methods of Measurement of Interference
Characteristics of IT Equipment
EN 60950-1:2006 + A1:2010 + A11:2009 + A12:2011
IEC 60950-1 (ed.2);am1- Product Safety Standard.
Signed for and on behalf of CognitiveTPG, LLC
Ithaca, NY, January 2, 2013
Jeffrey C Phoenix, Regulatory Compliance Engineer, CognitiveTPG, LLC Ref #: 189-1300058 Rev H
3
Choose a location for the printer.
4
Connect the following cables based on your configuration, using a-d below.
When using USB (step “b” below),
use caution to ensure the USB
cable is connected to the USB
connector and not into the
cash drawer connector that is
on the right back of the printer.
RS-232C
Communication
Connector
USB
Connector
Power
Supply
Connector
Cash
Drawer
Connector
Connector
Interface
Panel
����
�����
�������������
�����������������
�������������������
a
Cash drawer (if your installation includes this feature, page 17).
b
9-pin serial or USB cable (serial: page 18; USB: page 19).
c
Connect the power cable (page 20).
d
Route cables as shown for your setup configuration (page 21). All cables shown for
routing purposes only. Do not connect USB and RS232 cables at the same time.
5
Run a diagnostic test (page 24).
- Set Firmware Features - > 8 clicks
*** A799II - Diagnostics Form ***
Model number : A799-780D-TD00
Serial number : 0000000000
Flash Firmware
Revision : V1.22
CRC : 07AE
P/N : 189-799A122A
H/W parameters
Flash Memory Size : 8 Mbytes
Flash Logos/Fonts : 640 kbytes
Flash User Storage : 0 kbytes
Flash Perm’nt Fonts : 5504 kbytes
Flash Journal Size : 0 kbytes
SRAM Size : 8192 kbytes
Head settting : H
Motor ID : 1
Paper Type Setting : Type 0, Monochrome
Color Density Adj : n/a
Print Density, Mono : 80%
Max Speed : 350 mm/sec
Paper Width : 80 mm
Max Power : Level 1
Knife : Enabled
Partial Cut : 135 steps
Paper Low Sensor : Enabled
No Paper Low Extension
Comm. Interface
Interface : USB
RX Buffer Size : 4096
USB Driver Type : Printer Class
Interface : RS232
RX Buffer Size : 4096
Parameters
Baud Rate : 115200
Data Bits : 8
Stop Bit : 1
Parity : NONE
Flow Control : DTR/DSR
Reception Errors : Ignore
Resident Code Pages : 437, 850, 852, 858
860, 863, 865, 866
1252, 862, 737, 857
1251, 1255, KZ-1048
Press Feed Button Within the
Next Two Seconds
***To Enter Printer Config Menu***