Controlled Products Systems Group SK-1123-SQ - Manual

Digital Access Keypad Manual
® PIHAK1
SECO-LARM U.S.A., Inc.
MiSK-1123-SQ_092810.pmd
® ®
SECO-LARM
Note: Model numbers that end with "Q" or that have a round green "Q" sticker signify RoHS-compliant products.
Outdoor Digital Access Keypad
with 2 Outputs
SK-1123-SQ
MANUAL
SECO-LARM ® U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606
Tel: 800-662-0800 / 949-261-2999 Fax: 949-261-7326 Website: www.seco-larm.com
E-mail: [email protected]
LIFETIME LIMITED WARRANTY This SECO-LARM product is warranted against defects in material and workmanship while
used in normal service for the lifetime of the product. SECO-LARM’s obligation is limited to the repair or replacement of any defective part
if the unit is returned, transportation prepaid, to SECO-LARM. Under no circumstances will SECO-LARM be responsible for any costs or
charges for removal, installation, or reinstallation. This Warranty is void if damage is caused by or attributed to acts of God, physical or
electrical misuse or abuse, neglect, repair, or alteration, improper or abnormal usage, or faulty installation, or if for any other reason
SECO-LARM determines that such equipment is not operating properly as a result of causes other than defects in material and
workmanship. The sole obligation of SECO-LARM, and the purchaser’s exclusive remedy, shall be limited to repair or replacement only, at
SECO-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or property
damages of any kind to the purchaser or anyone else. This lifetime limited warranty is for products sold and installed in the United States
and Canada. For all other countries the warranty is 1 (one) year.
NOTICE: The information and specifications printed in this manual are current at the time of publication. However, the SECO-LARM
policy is one of continual development and improvement. For this reason, SECO-LARM reserves the right to change specifications without
notice. SECO-LARM is also not responsible for misprints or typographical errors. Copyright © 2010 SECO-LARM U.S.A., Inc. All rights
reserved. This material may not be reproduced or copied, in whole or in part, without the written permission of SECO-LARM.
SK-1011-SQ SK-1131-SQ SK-2323-SDQ SK-1323-SDQ
Indoor Keypads Outdoor Keypads
Also available from SECO-LARM:
SK-1123-FQ
®
ENFORCER
u u u u
X X X X
X X X X
X X X X *
*
#
#
#
#
1
1
1
#
X X X X # 2
u u u u
u u u u
u u u u
2 # u u u u
# 2
X X X X # 0
*
Note: indicates
the user code.
Note: indicates
the master code.
Quick Reference Guide
1. Using the User Codes:
A. User codes operate the door (4-8 digits long).
Press
B. The key must be pressed also if the keypad is in manual-entry mode.
Press
2. Using the Master Code:
The Master Code can be used to operate the door or program the keypad (4-8 digits long, see pt. 5 below).
Press (Relay output #1)
Press (Relay output #2)
3. Using the Inhibit/Lockout Code:
Please contact your installer for an explanation of inhibit mode and its operation.
4. Using Duress Codes:
For a full explanation of duress codes and their uses, see pg. 12.
5. Delete/Add/Change User and Master Code:
WARNING -- Press the correct option key. If the option key is not used and a "0" is pressed after
entering the Master Code, it could accidentally reprogram the Master Code.
A. Enter the Master Code first, followed by the key
(If you forgot the master code, see page 15 for more information.
Press
B. Changing/Adding Users:
Press 00-99 (user ID) (user code, 4-8 digits) (for relay output #1)
Press 0-9 (user ID) (user code, 4-8 digits) (for relay output #2)
C. Deleting Individual Users:
Press 00-99 (user ID) (for relay output #1)
Press 0-9 (user ID) (for relay output #2)
D. Changing the Master Code:
Press
E. To exit programming mode, press the key.
Page 16