Controlled Products Systems Group DT-4A - Manual

INS
T
R,CO
D
E
SE
T
,D
T
4
Linea
r P/N:
1060
88 D
Size: 8.
500" x 1
1
.00
0
"
Ma
teri
a
l:
20 L
b
. M
ead
Bond
Ink: Bl
ac
k
Scale: 1
-1
DT-4B
DIGITAL
TRANSMITTER
Code Setting
Instructions
(800) 421-1587
•
www.linearcorp.com
DESCRIPTION The Delta-3 DT-4B digital transmitter is a
four-channel wireless radio control designed for use with
automatic garage/gate operators and access control systems. The
transmitter can be used with one four-channel receiver (DR4), two
two-channel receivers (DR2) or four single-channel receivers (DR,DRQ
or DRM). Receivers should be mounted at least 8 feet apart.
The Delta-3 radio format provides 256 different digital codes. The
codes are set using the 8-position coding switches in the units.
✶ CAUTION: All transmitters and receivers should be
recoded by the installer prior to operation.
In order to avoid the possibility of duplicating codes in adjacent
systems, factory set codes should not be used. In addition, among
the valid codes available, four others should not be used. These
include: all keys set ON or OFF and keys set alternating ON/OFF.
The transmitter is powered by a 9-volt battery. It should last 12 to
18 months with normal use. The red LED on the face of the
transmitter will glow when the unit is activated. When it lights dimly,
or not at all when transmitting, the battery needs to be replaced.
STEP 1 Locate coding switch. Remove the battery access door
located on the back of the transmitter case. Identify the coding
switch and note that it has eight positions, with ON and OFF clearly
labeled.
STEP 2A Coding for single-channel receivers. P i c k a n y
combination of OFF/ON codes and set them on switch keys 3-8 in
the transmitter. Match the same code on switch keys 3-8 in each
receiver. Set each receiver’s switch keys 1 and 2 to select which
transmitter button will activate it. Transmitter switch keys 1 & 2
are unused and can be in any position.
STEP 2B Coding for two-channel receivers. P i c k a n y
combination of OFF/ON codes and set them on switch keys 3-8 in
the transmitter. Match the same code on switch keys 3-8 in each
receiver. Set each receiver’s switch key 2 to select which
transmitter buttons (1 & 2, or 3 & 4) will activate it. Transmitter
switch keys 1 & 2 and receiver switch key 1 are unused and
can be in any position.
STEP 2C Coding for a four-channel receiver. P i c k a n y
combination of OFF/ON codes and set them on switch keys 3-8 in
the transmitter. Match the same code on switch keys 3-8 in each
receiver. Transmitter and receiver switch keys 1 & 2 are
unused and can be in any position.
STEP 3 Test the equipment. Connect the receiver(s) to the
operators as described in the receiver’s installation instructions.
Be sure the door/gate area is clear. Activate the transmitter and
verify that the receiver triggers the operator. Check that the correct
button on the DT-4B activates the desired operator.
BATTERY REPLACEMENT
The battery should last 12 to 18 months with normal use. The red
LED on the face of the transmitter will glow when the unit is
activated. When the red LED lights dimly, or not at all when
transmitting, the battery needs to be replaced. Remove the battery
access door to change the battery. Any type of 9-volt battery can
be used.
LINEAR LIMITED WARRANTY
This product is warranted to the consumer against defects in material and workmanship for one year from the
date of purchase. This warranty applies to first retail buyers of new devices. Warrantor will repair, or at its option,
replace, any device it finds that requires service under this warranty, and will return the repaired or replaced
device to the consumer at the warrantor’s cost. For warranty service and shipping instructions contact warrantor
at the address shown below. Devices must be sent to warrantor for service at owner’s expense. The remedies
provided by this warranty are exclusive. Implied warranties under state law are to the one year period of this
written warranty. Some states do not allow limitations on how long an implied warranty lasts, so the above
limitation may not apply to you. In order to be protected by this warranty, save your proof of purchase and send
copy with equipment should repair be required. This warranty gives you specific legal rights, and you may also
have other rights which vary from state to state.
All products returned for warranty service require a Return Product Authorization Number (RPA#). Contact
Linear Technical Services at 1-800-421-1587 for an RPA# and other important details.
IMPORTANT !!!
Linear radio controls provide a reliable communications link and fill an important need in portable wireless
signaling. However, there are some limitations which must be observed.
✶ For U.S. installations only: The radios are required to comply with FCC Rules and Regulations as Part 15
devices. As such, they have limited transmitter power and therefore limited range.
✶ A receiver cannot respond to more than one transmitted signal at a time and may be blocked by radio signals
that occur on or near their operating frequencies, regardless of code settings.
✶ Changes or modifications to the device may void FCC compliance.
✶ Infrequently used radio links should be tested regularly to protect against undetected interference or fault.
✶ A general knowledge of radio and its vagaries should be gained prior to acting as a wholesale distributor or
dealer, and these facts should be communicated to the ultimate users.
This device complies with FCC Rules Part 15. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Copyright © 1999 Linear Corporation 106088 D
REMOVE BATTERY
ACCESS DOOR
CODING
SWITCH
DT-4B CODING SWITCH
SET KEYS
3-8 TO ANY
CODE
KEYS 1 & 2
ARE UNUSED
MATCH
3-8 MATCH
3-8
MATCH
3-8 MATCH
3-8
CODING SWITCHES IN DR RECEIVERS
1 & 2
OFF 1 ON
2 OFF
1 OFF
2 ON 1 & 2
ON
TRIGGERS FROM BUTTON 1 TRIGGERS FROM BUTTON 2
TRIGGERS FROM BUTTON 3 TRIGGERS FROM BUTTON 4
RECEIVER
#1
RECEIVER
#3
RECEIVER
#2
RECEIVER
#4
DT-4B CODING SWITCH
SET KEYS
3-8 TO ANY
CODE
KEYS 1 & 2
ARE UNUSED
MATCH
3-8
MATCH
3-8
CODING SWITCHES IN DR2 RECEIVERS
KEY 2
OFF
KEY 2
ON
TRIGGERS FROM
BUTTONS 1 & 2
TRIGGERS FROM
BUTTONS 3 & 4
KEY 1
UNUSED
KEY 1
UNUSED
RECEIVER
#1
RECEIVER
#2
DT-4B CODING SWITCH
SET KEYS
3-8 TO ANY
CODE
KEYS 1 & 2
ARE UNUSED
CODING SWITCH IN DR4 RECEIVER
MATCH KEYS
3-8 TO DT-4B
KEYS 1 & 2
ARE UNUSED
REPLACE BATTERY WITH
FRESH 9-VOLT BATTERY
WARNING!
BE SURE DOOR
AREA IS CLEAR
OF OBSTRUCTIONS
ACTIVATE TRANSMITTER
TO TEST EQUIPMENT