Controlled Products Systems Group DTKP - Manual

IN
S
T
R,INS
T,DTK
P
L
in
ear P/N: 20
942
0 B
M
a
te
rial: 20
Lb.
Mea
d Bo
nd
Si
ze:
8.50
0" x 11.
000"
In
k
: B
la
c
k
Sc
al
e: 1
-1
DTKP
DIGITAL
KEYPAD
TRANSMITTER
Installation
Instructions
(800) 421-1587 • www.linearcorp.com
DESCRIPTION
The Delta-3 DTKP Keypad is one of Linear’s series
of wireless radio controls designed for use with
automatic garage door and gate operators. The
Delta-3 radio format provides 256 different codes.
In operation, the user enters their unique code on
the unit’s keypad and presses the START/STOP
button to activate the door operator. For up to 30
seconds after the last activation, the DTKP can be
re-triggered by simply pressing the START/STOP
button again. This allows the user to stop or reverse
the opener quickly, without having to re-enter their
code.
The DTKP has built-in keypad lighting for use at
n i g h t o r i n d a r k a r e a s . B y p r e s s i n g t h e
START/STOP button first, before entering their
code (or pressing START/STOP twice at any time),
the user can light up the keypad. The clear silicone
keys are backlit with a pleasing green glow.
Standard Digital receivers are programmed by
setting an 8-position dipswitch in the receiver. The
DTKP will match the receiver’s code when the
correct number keys are pressed before the
START/STOP key. The correct code for the
DTKP matches the “ON” positions of the
receiver. T h e c o d e m us t be e nt e re d i n
descending order. Keys 0 and 9 are not used on
the DTKP. A keypad lockout timer will disable the
keypad after 3 code entry attempts. The keypad
must remain idle for 30 seconds before new
attempts can be made. STEP 1 Check receiver’s code. Locate the
coding dipswitch on the receiver. On some
receivers (Model DR) the switch is hidden when
the receiver is mounted on the door operator.
Loosen the three terminal screws to remove the
receiver and examine the coding switch. From
8 to 1, write down the numbers of all the “ON”
switch positions.
STEP 2 Verify Receiver Installation. B e
sure the receiver is reconnected (if removed) to
the garage door operator as described in the
receiver’s Installation Instructions.
STEP 3 Test receiver. Be sure door area is
clear. Try the keypad code. Enter a digit for each
receiver switch “ON” position in descending
order. The operator should activate when the
START/STOP button is pressed after entering
the valid keypad code.
STEP 4 Mount keypad. Use the two screws
and screw anchors provided to mount the
keypad to the wall. Be sure the keypad is at least
five feet above the ground. After mounting the
keypad, cover the screw heads using the two
plugs supplied.
STEP 5 Operation keystrokes. S e e t h e
i l l u s t r a t i o n f o r e xa m p le s o f d a y t im e a n d
nighttime operation.
INFO 1A Opening battery compartment.
The DTKP battery should last up to 5 years with
normal use. To remove the battery door to
replace the battery, remove the battery door
retaining screws and slide the battery door off.
INFO 1B Replacing battery. Remove the
low battery and replace it with a fresh 9-volt
alkaline or lithium battery. Replace the battery
door and retaining screws.
LIMITED WARRANTY
This product is warranted to the consumer against defects in material and
workmanship for one year from the date of purchase. This warranty applies
to first retail buyers of new devices. Warrantor will repair, or at its option,
replace, any device it finds that requires service under this warranty, and
will return the repaired or replaced device to the consumer at the warrantor’s
cost. For warranty service and shipping instructions contact warrantor at the
address shown below. Devices must be sent to warrantor for service at
owner’s expense. The remedies provided by this warranty are exclusive.
Implied warranties under state law are to the one year period of this written
warranty. Some states do not allow limitations on how long an implied
warranty lasts, so the above limitation may not apply to you. In order to be
protected by this warranty, save your proof of purchase and send copy with
equipment should repair be required. This warranty gives you specific legal
rights, and you may also have other rights which vary from state to state.
All products returned for warranty service require a Return Product
Authorization Number (RPA#). Contact Linear Technical Services at
1-800-421-1587 for an RPA# and other important details.
IMPORTANT !!!
Linear radio controls provide a reliable communications link and fill an
important need in portable wireless signaling. However, there are some
limitations which must be observed.
✶ For U.S. installations only: The radios are required to comply with FCC
Rules and Regulations as Part 15 devices. As such, they have limited
transmitter power and therefore limited range.
✶ A receiver cannot respond to more than one transmitted signal at a time
and may be blocked by radio signals that occur on or near their operating
frequencies, regardless of code settings.
✶ Changes or modifications to the device may void FCC compliance.
✶ Infrequently used radio links should be tested regularly to protect against
undetected interference or fault.
✶ A general knowledge of radio and its vagaries should be gained prior to
acting as a wholesale distributor or dealer, and these facts should be
communicated to the ultimate users.
Copyright © 1999 Linear Corporation 209420 B
ENTER CODE
AND PRESS
START/STOP
W X
Y
G H I
D E F A B C J
K L M
N O
P
R S T
U V
WARNING!
BE SURE DOOR
AREA IS CLEAR
OF OBSTRUCTIONS
REMOVE
RETAINING
SCREWS AND
BATTERY DOOR
REPLACE
WITH 9-VOLT
ALKALINE OR
LITHIUM
BATTERY ONLY
USE SCREW
ANCHORS
PROVIDED
COVER SCREWS
WITH PLUGS
MOUNT
KEYPAD
TO WALL
SWITCHES IN
RECEIVER
THIS SWITCH
HAS 6, 3 & 2 ON
DTKP CODE
FOR THIS
RECEIVER:
D E F
M N O
RECONNECT RECEIVER TO GARAGE DOOR OPERATOR
D E F
M N O
A B C
DAYTIME OPERATION
NIGHTTIME OPERATION
PRESS:
USER'S SECRET CODE
D E F
M N O
A B C
PRESS:
USER'S SECRET CODE LIGHTS
KEYPAD
PRESS: LIGHTS
KEYPAD