Controlled Products Systems Group MVP-1CH-12V-3W-FC - Manual

4
P/N 190-111676 REV B
After installing your receiver and transmitter, check the
operation of your radio controls by moving
approximately 45 feet back from the garage door, then
press the transmitter button. Operation at this distance
should be reliable. However, environmental conditions
and the location of the transmitter and receiver will
affect distance.
•
If the transmitter doesn’t activate the operator check the
coding on both the transmitter and receiver. The code
setting must match exactly . This may necessitate a
reprogramming of the transmitter and receiver.
•
If the distance is inadequate check the battery and
replace if necessary.
•
To maximize the operating distance move the
transmitter to different locations in the car until a
satisfactory distance is achieved. Vanity mirrors on sun
visors will affect performance.
•
If the receiver is in the proximity of a metal beam or
other obstruction it may be necessary to relocate the
receiver to increase the operating range.
•
If multiple receivers are mounted closer than 15 feet,
blocking and interference may occur. Move the
receivers further apart.
•
If system does not work at any distance, check that the
receiver terminals are connected to the proper operator
terminals.
•
If the HomeLink® transmitter does not activate the
operator or distance is inadequate,verify proper
operation using the hand-held transmitter. Contact your
HomeLink® system provider for help with
configuring the HomeLink® transmitter and to resolve
distance problems when using the HomeLink® system.
Operational Check
This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry
Canada. Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
WARNING
Unexpected door operations can cause personal injury or property damage.
LINEAR LIMITED WARRANTY
This product is warranted to the consumer against defects in material and
workmanship for one year from the date of purchase. This warranty applies to first
retail buyers of new devices. Warrantor will repair, or at its option, replace, any device
it finds that requires service under this warranty, and will return the repaired or
replaced device to the consumer at the warrantor’s cost. For warrant service and
shipping instructions contact warrantor at the address shown below. Devices must be
sent to warrantor for service at owner’s expense. The remedies provided by this
warranty are exclusive. Implied warranties under state law are to the one year period
of this written warranty. Some states do not allow limitations on how long an implied
warranty lasts, so the above limitation may not apply to you. In order to be protected
by this warranty, save your proof of purchase and send copy with equipment should
repair be required. This warranty gives you specific legal rights, and you may also
have other rights which vary from state to state.
For warranty service and shipping instructions contact Linear at the phone number
shown below. In order to be protected by this warranty, save your proof of purchase
and send a copy with equipment should repair be required. All products returned for
warranty service require a Return Product Authorization Number (RPA#). Contact
Linear Technical Services at 1-800-421-1587 for an RPA# and other important details.
MVP Radio Controls are compatible with HomeLink ®.
Homelink ® is a registered trade mark of Johnson Controls, Inc.
Installation on Operators that Provide
Power for Receivers
Some operators can provide power for an
external receiver. Disconnect power to the
operator before installing receiver. Connect
terminals 1, 2 & 3 of the receiver to terminals
1, 2 & 3 on the operator.
3
2
1 3
2
1
3 2 1
P B
Disconnect power to operator
before any installation or repair.
Follow all instructions provided by
the manufacturer of your operator.
WARNING
Two and Three Door Installations
The receiver is installed on the left side of a
two-door and in the center of a three-door
(outside facing into the garage). Connect the
receiver per instructions above (operators with
or without receiver power). The additional wire
leads are connected to terminals 1 & 2 or P & B
of the second or second & third operator.
Garage Door and Gate Operator Radio Controls
MVP Receiver and Transmitters
Product Features
These controls are designed to remotely operate
garage door and gate openers. The MVP
receiver is compatible with Classic, MVP and
Original Allstar, Allister and Pulsar type dip-
switch transmitters. The MVP receiver is
available in one and three-door versions and
may be used as shown below.The radio
frequency of the remote controls is fixed and
tuned at the factory. RF adjustments are not
required and should not be attempted by the
end user. There are no user serviceable parts in
the radio controls.
Receiver Installation
First, determine the type of operator (with or
without receiver power). Refer to the operator
manual or contact the operator manufacturer as
needed. Next, attach the receiver to the operator
according to the appropriate installation
instructions. For two and three door
installations connect the wire leads from the
receiver to the second or second and third
operator. Next, set the transmitter codes
according to the instructions provided with the
transmitter. To finish, program the receiver
with the transmitter codes.
One-Door Installation Two-Door Installation Three-Door Installation
1 2 1 1 2 3
Installation on Operator Without
Power for Receivers
Some operators do not provide power for an
external receiver. An optional transformer and
wire kit is required. Disconnect power to the
operator before installing receiver. Connect
terminals 1 & 3 of the receiver to the
transformer. Connect terminals 1 & 2 on the
receiver to terminals P & B on the operator.
USA & Canada
(800) 421-1587 & (800) 392-0123
(760) 438-7000
Toll Free FAX (800) 468-1340
www.linearcorp.com