DoorKing 1812 Plus - Manual (Page 30)

1812-161-L-12-11 28
2.5.4 Delete All Access Codes (Simple and Time Zone Restricted)
This programming sequence ONLY deletes ALL existing ”simple” and “time zone restricted” access codes that have been
programmed into the system. “temporary” access codes CANNOT be deleted. If you require all “temporary” access codes
to be deleted, use the programming sequence in 2.5.7.
WARNING: Once started, all ”simple” and “time zone restricted” access codes will be erased.
1. Press * 7 2 and enter the MASTER CODE. [ * 7 2 _ _ _ _ (beep)]
2. Press 2, then press * . [ 2 * (beep)]
3. Press 9 9 9 9, then press * . [ 9 9 9 9 (beep)]
4. The programming sequence will end itself automatically. [beeeeeep]
2.5.6 Delete a “Temporary” Access Code
This programming sequence deletes individual existing “temporary” access codes that have been programmed into the
system. “simple” and/or “time zone restricted” access codes CANNOT be deleted. If you require “simple” and/or “time zone
restricted” access codes to be individually deleted, use the programming sequence in 2.5.3.
1. Press * 7 4 and enter the MASTER CODE. [ * 7 4 _ _ _ _ (beep)]
2. Press 2, then press * . [ 2 * (beep)]
3. Enter the five-digit “temporary” access code to be deleted, then press * . [ _ _ _ _ _ * (beep)]
See 2.5.5 for the five-digit “temporary” access code(s).
4. Repeat steps 2 and 3 to delete additional existing “temporary” access codes.
5. Press 0 # TOGETHER to end. [0 # (beeeeeep)]
2.5.5 “Temporary” Access Code Programming
This programming sequence programs up to 10 “temporary” access codes with a beginning and ending date and any time
zone restrictions that may need to be applied.
1. Press * 7 3 and enter the MASTER CODE. [ * 7 3 _ _ _ _ (beep)]
2. Press 2, then press * . [ 2 * (beep)]
3. Choose and enter a five-digit “temporary” access code, then press * . [ _ _ _ _ _ * (beep)]
4. Enter the beginning month (01 to 12) and day (01 to 31), then press * . [ _ _ _ _ * (beep)]
5. Enter the ending month (01 to 12) and day (01 to 31), then press * . [ _ _ _ _ * (beep)]
6. Enter a minimum of 1, and a maximum of 4 time zones (valid time zones are 0 through 6) that you
want to apply to this access code, then press
* . [ _ _ _ _ * (beep)]
Time zone 0 - Always deny access.
Time zone 1 - Allows 24/7 access for relay 1 ONLY.
Time zone 2 - Allows 24/7 access for relay 2 ONLY.
Time zones 3, 4, 5 and 6 - Are time zones that have been programmed in 2.6.6.
7. Enter 0 * for momentary relay activation OR enter 1 * to hold open (latch) the relay. [ _ * (beep)]
8. Repeat steps 2 through 7 to program additional “temporary” access codes.
9. Press 0 # TOGETHER to end. [0 # (beeeeeep)]
2.5.7 Delete All “Temporary” Access Codes
This programming sequence ONLY deletes ALL existing “temporary” access codes that have been programmed into the
system. “simple” and “time zone restricted” access codes CANNOT be deleted. If you require all “simple” and “time zone
restricted” access codes to be deleted, use the programming sequence in 2.5.4.
WARNING: Once started, all “temporary” access codes will be erased.
1. Press * 7 5 and enter the MASTER CODE. [ * 7 5 _ _ _ _ (beep)]
2. Press 9 9 9 9, then press * . [ 9 9 9 9 (beep)]
3. The programming sequence will end itself automatically. [beeeeeep]