LEADER LV 58SER06 - Manual (Page 2)

34
Amplitude Accuracy ±0.5 %
Horizontal Axis
Line Display
Display Format Overlay: 1H, 2H
Parade: 1H, 2H, 3H
Magnification x1, x10, x20, ACTIVE, or BLANK
Cursor Measurement
Composition
Horizontal Cursors 2 (REF and DELTA)
Vertical Cursors 2 (REF and DELTA)
Amplitude Measurement Percentage and voltage displays
Time Measurement Second display
Frequency Measurement Computes and displays the frequency with the
length of one period set to the time between two
cursors
Vectorscope Display
Scale 75 % or 100 % (color bar)
Gain x1, x5, IQ-MAG, or variable
Variable Gain x0.2 to x10
Amplitude Accuracy ±0.5 %
IQ Axis Show or hide
Pseudo-Composite Display Converts component signals into composite sig-
nals with artificially added burst and displays the
results (The color matrix is converted to SDTV.)
Picture Display
Display Format Samples pixels and displays them (R, G, and B
each use 8 bits)
Marker Displays Center marker, 4:3 marker, safe action marker,and
safe title marker
Gamut Error Display Marks the areas of the picture that exhibit gamut
errors
Line Select Marks the selected line
Display Sizes Compressed and full frame
Status Display
3G-SDI Signal Status Display
Signal Detection Detects the presence of a 3G-SDI signal
Format Detects from the supported video signal formats
(When the LV 58SER06 is configured to automati-
cally set the format, the format is detected from
the payload ID.)
Embedded Audio Channel Displays the embedded audio channel number
(Only the audio data of data stream 1 is supported.)
3G-SDI Signal Error Detection
CRC Error Detects 3G-SDI signal transmission errors
TRS Error Detects TRS position and protection bit errors
Line Number Error Detects 3G-SDI signal line number errors
Illegal Code Error Detects data within the range of 000h to 003h and
3FC to 3FF in locations other than the TRS and
ADF headers
Ancillary Data Error Detection
Checksum Error Detects ancillary data transmission errors
Parity Error Detects ancillary data header parity errors
Image Quality Error Detection
Frequency Response Approx. 1 MHz LPF (IEEE STD 205 response) and
approx. 2.8 MHz LPF (removes transient compos-
ite gamut and gamut errors due to overshoot and
other anomalies)
Gamut Error Detects time-specified gamut errors
Upper Limit 90.8 to 109.4 %
Lower Limit –7.2 to 6.1 %
Area Specification 0.1 to 5.0 %
Time Specification 1 to 60 frames
Composite Gamut Error Detects level errors that occur when component
signals are converted to composite signals
Upper Limit 90.0 to 135.0 %
Lower Limit –40.0 to 20.0 %
Area Specification 0.1 to 5.0 %
Time Specification 1 to 60 frames
Embedded Audio Error Detection
(Only data stream 1 is supported
for 3G-SDI level B.)
BCH Error Detects transmission errors in the audio packets
that are embedded in 3G-SDI signals
DBN Error Detects audio packet continuity errors
Parity Error Detects parity errors in the audio packets that are
embedded in 3G-SDI signals
Embedded Position Error Detects the presence of audio in lines where it
should not be embedded
Event Log
Recorded Events Errors, changes in the input channel, and time
stamps
5 Bar Display
Bar Display Displays the Y GBR component and composite
gamut
(When you are using line select, only the compo-
nent gamut of the selected line is detected.)
Error Level Setting
Component Gamut The same as the gamut error
Composite Gamut The same as the composite gamut error
Frequency Response The same as the gamut error
Analysis Features
Data Dump Display
Display Format Displays data separated by serial data sequence
or by channel
(The 3G-SDI level B data dump can display data
stream 1, data stream 2, and data stream 1 and 2
simultaneously.)
Line Select Displays the selected line
Sample Select Displays from the selected sample
Jump Feature Moves to EAV or SAV with the press of a single
button
Data Output Data can be saved as text files to USB memory or
to a PC over an Ethernet
Audio Control Packet Display
(Only data stream 1 is
supported for 3G-SDI level B.)
Display Details Displays audio control packet analysis
Display Format Text, hexadecimal, and binary
Group Selection Select one group from four available groups
Format ID Display
Corresponding Standard SMPTE 352M
Display Details
Displays payload ID packet analysis
ANC Packet Display
(Only data stream 1 is
supported for 3G-SDI level B.)
ANC Specification Method DID/SDID
Display Format Hexadecimal and binary
Time Code Display
(Only data stream 1 is
supported for 3G-SDI level B.)
Supported Time Codes LTC and VITC (SMPTE 12M-2)
Display Mode The instrument's internal clock or the time code
Embedded Audio Processing
Clock Generation Generated from the video clock
Synchronization All audio channels must be synchronized to the
video clock.
Phases All phases must be in-sync.
Channel Separation You may select a maximum of 4 groups of 16
channels each.
(Only data stream 1 is supported for 3G-SDI level B.)
* You need an LV 58SER40A unit to display and
generate audio.
Frame Capture Feature
Function Captures frame data
Capture Timing Manual and automatic (error capture)
Display Displays the captured frame data or superimposes
the captured frame data over the input signal
Media Internal memory (RAM) and USB memory
You can only record one frame of data to the inter-
nal memory.
Data Output Screen captures can be saved as .dpx files, .tif
files, or in a file format that the instrument can
load. They can be saved to USB memory or sent
to a PC through an Ethernet connection.
Data Input Data saved to USB memory can be loaded and
displayed on the instrument.*1
Error Capturing Automatically captures frame data when an error
occurs
*1 Captured data cannot be displayed unless the
instrument is receiving a 3G-SDI signal that
matches the format of the captured signal.
Environmental Conditions Conforms to those for the LV 5800 or LV 7800
Power Consumption Supplied from the instrument; 18 W max.
Weight 0.24 kg
0.53 lbs.
Accessory Instruction manual .............................................1
LV 5800/LV 7800 Platform Options
Leader Instruments Corporation web : http://www.LeaderUSA.com Tel. : 1 (714) 527‐9300
6484 Commerce Drive, Cypress, CA 90630 e‐mail : [email protected] Fax : 1 (714) 527‐7490