Lectrosonics SRb_SRb5P - Manual (Page 6)

SRb5P and SRb Dual Receivers
LECTROSONICS, INC. 6
RF Front-End and Mixer
Each antenna signal is first passed through a high qual-
ity SAW filter to reject high power RF signals above and
below the operating frequency. A high current amplifier
follows the SAW filters and passes the signal to an in-
ternal splitter so that both antenna signals are available
to both receivers for SmartDiversity™ reception.
The mixer in each receiver takes the signal from the
PLL to generate the first IF signal, with both PLL circuits
fed from a common reference oscillator to maintain
signal phase through the IF sections.
Microcontroller, PLL and VCO Circuits
The 8-bit microprocessor is the “heart” of the SRb5P
and SRb receivers. It monitors user command inputs
from the front panel control buttons and numerous other
internal signals such as RF level, audio levels, pilot tone
levels and transmitter battery status. Outputs from the
microcontroller drive the LCD display and backlight, and
control the squelch, the audio output attenuator, the
PLL/VCO circuits and the antenna phase switch.
IF Amplifiers and SAW Filters
The first IF stage employs two SAW (surface acoustic
wave) filters. The use of two filters significantly increas-
es the depth of filtering while preserving sharp skirts,
constant group delay, and wide bandwidth. Though ex-
pensive, this special type of filter allows primary filtering
as early as possible, at as high a frequency as possible,
before high gain is applied, to deliver maximum image
rejection. Since these filters are made of quartz, they
are very temperature stable.
After the SAW filter, the IF signal is converted to 350
kHz in receiver 1 and 250 kHz in receiver 2. Only then
is the majority of the gain applied, just before the signal
is converted to audio with a pulse counting detector.
Although these IF frequencies are unconventional in a
wide deviation (±75 kHz) system, it offers outstanding
AM rejection over a very wide range of signal strengths
and improved noise performance.
Digital Pulse Counting Detector
The receiver uses an elegantly simple, yet highly effec-
tive digital pulse detector to demodulate the FM signal,
rather than a conventional quadrature detector. This
unusual design eliminates thermal drift, improves AM
rejection, and provides very low audio distortion.
DSP-Based Pilot Tone
The Digital Hybrid system design uses a DSP gener-
ated ultrasonic pilot tone to control the receiver audio
muting (squelch). The pilot tone frequency is different
for each of the 256 frequencies in the tuning range of a
system (frequency block). This eliminates squelch prob-
lems in multichannel systems where a pilot tone signal
can appear in the wrong receiver via intermodulation
products.
The DSP generated pilot tone also eliminates fragile
crystals, allowing the receiver to survive shocks and
mishandling much better than older analog-based pilot
tone systems.
Note: This description applies only to the Digital
Hybrid mode. In 200 Series, IFB and Mode 6
compatibility, only one pilot tone frequency is used
on all channels, emulating the original crystal-
based system. In other compatibility modes, no
pilot tone is used.
SmartSquelch ™
Any squelching system faces inevitable trade-offs:
squelch too aggressively and valuable audio information
may be lost. Squelch too little and excessive noise may
be heard. Respond too rapidly and the audio will sound
“choppy.” Respond too sluggishly and syllables or entire
words can be cut off.
SmartSquelch
TM combines several techniques to achieve
an optimal balance, removing distracting noise, without
the squelching action itself becoming a distraction. One
of these techniques involves waiting for a word or syl-
lable to complete before squelching. Another technique
incorporates recent squelching history and recent signal
strength, adjusting squelching behavior dynamically for
the most serviceable result under variable conditions. Us-
ing these and other techniques, the SRa5P and SRa can
deliver acceptable audio quality from otherwise unusable
signals.
Smart Noise Reduction (SmartNR ™ )
Note: The SmartNR setting is user selectable
only in the Digital Hybrid compatibility mode. In
other modes, noise reduction is applied in such a
way as to emulate the original analog system as
accurately as possible and is not user adjustable.
The wide dynamic range of digital hybrid technology,
combined with flat response to 20 kHz, makes it pos-
sible to hear the -120 dBV noise floor in the mic pre-
amp, or the (usually) greater noise from the microphone
itself. To put this in perspective, the noise generated
by the recommended 4k bias resistor of many electret
lavaliere mics is –119 dBV and the noise level of the
microphone’s electronics is even higher. In order to
reduce this noise the receiver is equipped with a Smart
Noise Reduction algorithm, which removes hiss without
sacrificing audio high frequency response.
The Smart Noise Reduction algorithm works by at-
tenuating only those portions of the audio signal that fit
a statistical profile for randomness or “electronic hiss.”
Because it is much more than a sophisticated variable
low pass filter, the transparency of the audio signal is
preserved. Desired high frequency signals having some
coherence are not affected, such as speech sibilance
and tones.