Mr. Gasket 5320 Alternator Pulley: Single Groove w/Nose Piece - Manual

Alternator Single Groove
Aluminum Pulley #5320
Fits most Delco and Ford Alternators
INSTALLATION INSTRUCTIONS
Follow this procedure to install this aluminum pulley:
1 . Remove negative (-) cable from battery and disconnect
wires from alternator. Be sure to note wire positions.
2 . Remove alternator from vehicle and place on bench
or suitable work area.
3 . Holding the center shaft with a hex wrench, loosen
and remove the pulley nut, washer and stock pulley.
4 . Remove the three #4 socket head screws from #5320
aluminum pulley and separate pulley and nose.
5 . Install aluminum pulley on alternator shaft with
raised spacer boss toward alternator.
6 . Replace stock washer and nut, then securely tighten
nut to 50 ft. lbs.
7 . Install pulley nose and securely tighten the three #4
socket head screws, using Loctite sealant on the threads.
CAUTION: Do not overtighten or you may strip the threads.
8 . Reinstall alternator on car, connect wires to proper
terminals, adjust belt to proper G.M. or Ford
specified tension.
9 . Be sure that all connections and mounting bolts
have been tightened correctly.
10 . Reconnect negative (-) battery cable.
Cleveland Ohio
www.mrgasket.com © 2000 Printed in U.S.A.
Alternator Single Groove
Aluminum Pulley #5320
Fits most Delco and Ford Alternators
INSTALLATION INSTRUCTIONS
Follow this procedure to install this aluminum pulley:
1 . Remove negative (-) cable from battery and disconnect
wires from alternator. Be sure to note wire positions.
2 . Remove alternator from vehicle and place on bench
or suitable work area.
3 . Holding the center shaft with a hex wrench, loosen
and remove the pulley nut, washer and stock pulley.
4 . Remove the three #4 socket head screws from #5320
aluminum pulley and separate pulley and nose.
5 . Install aluminum pulley on alternator shaft with
raised spacer boss toward alternator.
6 . Replace stock washer and nut, then securely tighten
nut to 50 ft. lbs.
7 . Install pulley nose and securely tighten the three #4
socket head screws, using Loctite sealant on the threads.
CAUTION: Do not overtighten or you may strip the threads.
8 . Reinstall alternator on car, connect wires to proper
terminals, adjust belt to proper G.M. or Ford
specified tension.
9 . Be sure that all connections and mounting bolts
have been tightened correctly.
10 . Reconnect negative (-) battery cable.
Cleveland Ohio
www.mrgasket.com © 2000 Printed in U.S.A.
Alternator Single Groove
Aluminum Pulley #5320
Fits most Delco and Ford Alternators
INSTALLATION INSTRUCTIONS
Follow this procedure to install this aluminum pulley:
1 . Remove negative (-) cable from battery and disconnect
wires from alternator. Be sure to note wire positions.
2 . Remove alternator from vehicle and place on bench
or suitable work area.
3 . Holding the center shaft with a hex wrench, loosen
and remove the pulley nut, washer and stock pulley.
4 . Remove the three #4 socket head screws from #5320
aluminum pulley and separate pulley and nose.
5 . Install aluminum pulley on alternator shaft with
raised spacer boss toward alternator.
6 . Replace stock washer and nut, then securely tighten
nut to 50 ft. lbs.
7 . Install pulley nose and securely tighten the three #4
socket head screws, using Loctite sealant on the threads.
CAUTION: Do not overtighten or you may strip the threads.
8 . Reinstall alternator on car, connect wires to proper
terminals, adjust belt to proper G.M. or Ford
specified tension.
9 . Be sure that all connections and mounting bolts
have been tightened correctly.
10 . Reconnect negative (-) battery cable.
Cleveland Ohio
www.mrgasket.com © 2000 Printed in U.S.A.
Alternator Single Groove
Aluminum Pulley #5320
Fits most Delco and Ford Alternators
INSTALLATION INSTRUCTIONS
Follow this procedure to install this aluminum pulley:
1 . Remove negative (-) cable from battery and disconnect
wires from alternator. Be sure to note wire positions.
2 . Remove alternator from vehicle and place on bench
or suitable work area.
3 . Holding the center shaft with a hex wrench, loosen
and remove the pulley nut, washer and stock pulley.
4 . Remove the three #4 socket head screws from #5320
aluminum pulley and separate pulley and nose.
5 . Install aluminum pulley on alternator shaft with
raised spacer boss toward alternator.
6 . Replace stock washer and nut, then securely tighten
nut to 50 ft. lbs.
7 . Install pulley nose and securely tighten the three #4
socket head screws, using Loctite sealant on the threads.
CAUTION: Do not overtighten or you may strip the threads.
8 . Reinstall alternator on car, connect wires to proper
terminals, adjust belt to proper G.M. or Ford
specified tension.
9 . Be sure that all connections and mounting bolts
have been tightened correctly.
10 . Reconnect negative (-) battery cable.
Cleveland Ohio
www.mrgasket.com © 2000 Printed in U.S.A.
100138-Inst.MRG5320 Alum Pulley 9/11/02 2:22 PM Page 1