Mr. Gasket 7668 Floor Shifter Conversion: 3-4 Speed Auto - Manual

UNIVERSAL FLOOR SHIFT
CONVERSION KIT
#7668
These instructions apply to the following MR. GASKET products:
7668 - Universal Floor Shift Conversion Kit, Fits Most Rear-Wheel Drive Car Applications
With Automatic Transmissions
INSTALLATION INSTRUCTIONS
WORK SAFELY
Perform this installation on a good, clean, level surface for
maximum safety and with the engine turned “OFF”.
Installation of this shifter requires working underneath the
vehicle. Raise vehicle by lifting at points specified by the
vehicle manufacturer. Place blocks or wedges in front of and
behind both rear wheels to prevent movement in either
direction. Support the vehicle with approved automotive
support stands or wheel ramps.
DO NOT USE A BUMPER JACK FOR SUPPORTING VEHICLE.
USE EXTREME CARE AND CAUTION WHEN WORKING
UNDERNEATH VEHICLE.
Never get near or under vehicle until you are confident that
it is safely supported and will not move or fall from its
raised position.
The following parts are included in this package:
Qty. Part No. Description
1 95090704 Shifter Assembly
1 97091050 Knob
1 114 8058 Rubber Boot
1 195 2590 Trim Plate
1 216 0001 Weather-Seal (Plastic Sheet)
1 170 0008Z Lever-Extender for Shifter
1 119 3783PO Rod Adjusting Button
2 97000015 Spring Clip
1 190 0001 3/32" x 3/4" Cotter Pin
1 213 0011Z Connecting Rod - Straight
1 213 0012Z Connecting Rod - Bent
1 195 0132Z Special Adapter
1 105 0007Z Transmission Arm/Adapter
1 105 0008Z Transmission Arm/Adapter
1 105 0009Z Transmission Arm/Adapter
1 105 0011Z Transmission Arm/Adapter
1 105 0012Z Transmission Arm/Adapter
2 265 0001 “U” Bolt – 1/4-20 Thread
1 265 0002 “U” Bolt – 1/4-28 Thread
6 97080969 1/4-20 x 1" Hex Head Cap Screw
1 215 0004 1/4-20 x 1-3/4" Head Cap Screw
10 97090082 1/4" Split Lockwasher
10 97000740 1/4-20 Hex Nut
4 267 3534 1/4" Flatwasher (5/64" Thick)
1 97090729 1/4" Flatwasher (1/16" Thick)
1 97090096 5/16-18 x 1" Hex Head Cap Screw
1 97000089 5/16" Split Lockwasher
1 97000670 5/16-18 Hex Nut
2 97000661 3/8-24 Hex Nut
1 97090062 3/8-24 Hex Jam Nut
1 97090058 3/8" Flatwasher
4 97090079 #10-12 x 1 Sheet Metal Screw
1 1540110 Hardware Kit
1 1010010 Ignition Block Adapter
1 1120007 Ignition Block
1 2280062 Spacer
2 2720008 Screw, 6-32 x 7/16
2 2720009 Screw, 6-32 x 5/8
SHIFTER INSTALLATION
1. Turn ignition key forward to unlock position on steering
column, if equipped, and place factory shifter in NEUTRAL
position.
Column shift applications: Remove drive pin that fastens
factory shifter lever to steering column, then remove lever
from column. Disconnect and remove shifter rod from
transmission. Do not remove rod to throttle.
Factory floor shift (console mount) applications:
Disconnect and remove console, shifter assembly, cable,
brackets and transmission arm if necessary. Do not
remove rod to throttle.
STEERING COLUMN LOCK-FOR 1969 & LATER VEHICLES
The SAFETY IGNITION BLOCK device supplied with this kit
MUST be installed as shown on page 6. It must be installed
to prevent the possibility of turning the ignition switch off
while vehicle is in motion. The steering column will lock
when this switch is turned off. Failure to heed this warning
could result in accidental steering lock-up while vehicle is in
motion.
2. Select a position for the shifter assembly on the center
line of floor tunnel. Punch or drill a small hole through
floor tunnel to mark location.
3. Check location underneath vehicle to be sure that shifter
will clear transmission rear support. Place template
supplied with this kit on the carpet. Locate “X” on
template over punched mark.
Trace outline of opening to be cut out on the carpet, then
carefully cut and remove carpet. Trace the outline of area
Qty. Part No. Description