Micromod MOD: Modcell 2050R Quick Reference Guide - Manual (Page 2)

operator accesses 12 menus through the setup keys
summarized in the chart on the reverse side. For
• Moves through the basic
Scroll:
• Advancestostepl. * BRD CALIBRAT
• Enters a YES response. ARE YOU SURE? YES, NO (If YES, all configura- or SKIP LOCKOUT RAT BIAS TYPE RATIO, BIAS, RAT BIAS SEG 1 SOAK TIM XXX. X (0 to 3000.0 hours or
Down: • Moves down through tion data is written over with TOTALIZE DI1 FUNC RUN/STOP, RUN/RSET, RATIO SOURCE LOCAL, REMOTE minutes)
menus. factory default values) RUN/HOLD (See IB-23C650) BIAS SOURCE LOCAL, REMOTE SEG 1 RMP RATE XXX. X (Change per unit time in
• Decreases values. CONFIG CHANGED For information only R/H, RSET LOCKOUT YES, NO (See IB-23C650 for RATIO BALANCE STANDARD (May bump when engineering units)
• Enters a NO response. SOFTWARE VERSION For information only or RESET LOCKOUT explanation) switching manual to auto), SEG 1 RELAY A ON, OFF
DISPLAY VERSION For information only or RUN/HOLD LOCKOUT AUTO (Bumpless Transfer) SEG 1 RELAY B ON, OFF
Top/Middle Display Bottom Display/Entry R/L KEY LOCKOUT YES, NO Not valid if source is remote. SEG 1 RELAY C ON, OFF
BASE CFG **MENU** INPUTS **NENU* LOC-REM ALLOWED NO, YES BIAS BALANCE Same entries as Ratio SEG 1 GUARANTD NO, YES
MAIN PWR FREQ 60 HERTZ, 50 HERTZ DECIMAL POINT 0., 0.0, 0.00, 0.000 DIG IN 1 ACTION REVERSE, DIRECT Balance SEG 2 SETUP Entry point for Segment 2.
PROC INP TYPE MILLIAMP (0 to 54 mA dc), PROC INP SETUP Entry point for input setup DIGITAL INPUT 2 Entry point for Digital Input 1. RATIO SOURCE LOCAL, REMOTE. For ratio and Same steps as for Segment 1.
VOLT (0 to 6V dc), PRC TEMP UNITS CELSIUS, FAHRENHT Same steps as Digital Inpu 1. Bias type. Only one remote Repeat for Segments 3-10.
THERMCPL (Thermocouple), PROC INP MA. HI XX. XX (1.00 to 54.00 mA dc), DI SETPT SEL LIST (15 combinations available, source allowed.
RTD (RTD Input), or MV. HI XX. X (0 to 120 mV dc), see IB-23C650 for listing) BIAS SOURCE LOCAL, REMOTE. For ratio and TOTALIZE **MENU**
MILLIVLT (-10 to 120 mV dc) or VOLTS. HI X.XX (0.00 to 5.OOV dc) Bias type. Only one remote WRAP AT PRED CNT NO (Counts until turned off or
SLIDEWIR (0 to 100% slide- PROC HI POSITION - X .XXX (0.000 to 1.000) MA. OUTP **NENU* source allowed. max. count reached),
wire wiper position) PROC INP MA. LO OUTPUT MA. HIGH XX.X (01.0 to 54.0 mA dc) RATIO BALANCE For Ratio and Bias type. Same YES (Counts to predetermined
PROC INP IC TYPE TYPE * (J, K, E, R, 5, T, B, N) or MV. LO XX. XX (0.00 to 53.00 mA do). OUTPUT MA. LOW XX.X (0 to mA High less 1 mA dc) entries as Ratio Balance. count & wraps to preset value)
PROCESS TEMP CAL Entry point tor temperature or VOLTS LO XX.X (-10.0 to llOmVdc). HEAT OUT HI LIMIT XX.X (0.1 to 110.00/0 of heat BIAS BALANCE For Ratio and Bias type. Same INPUT THRSHOLD XXXX (0 to Engineering Units
correction PROC LO POSITION XXX (0.00 to 4.90 V dc) output span) entries as Ratio Balance. High Value, in eng. units)
PR TEMP= XXX.X XX.X (XXX.X = Process tem- XXXX (0.000 to 0.900) COOL OUT HI LIMIT XX.X (0.1 tO 110.0% of cool TOTALIZE IS OFF For information only
perature, XX.X = Temperature PROCESS LIN TYPE NONE, SQR ROOT output span) SETPTS **MENU** or IS ON
correction [+15 to -15]) PROC ENG UNITS HI XXXX (-3000 to 30000) OUTPUT HI LIMIT XX.X (10.0 to 110% of mA LOC SETP Entry point for set-point setup TOTALIZE DIRECT UP, DOWN
INPUT 2 ENABLE NO, YES PROC ENG UNITS LO XXXX (-3000 to 30000) output span, 10.0 to 100% of LOC SETP FIXED NO, YES TOTALIZE RATE PER SEC, PER MIN, PER HOUR
INPUT 2 TYPE Same steps as Input1 type PR FAULT OUTPUT - XX (0 to 100%) relay output span) LOC SETP HI LIMIT XXXX (Low limit to 30000) SCALE DEC PT 0., 0.0, 0.00, 0.000
PR FAULT LEVL PCI XX (0 to 100%). See OUTPUT LO LIMIT XX.X (-8% or 0% relay to LOC SETP LO LIMIT XXXX (-3000 to high limit) SCALE FACTOR XXXX (0.001 TO 30000)
OUTPUT TYPE CUR PROP (Current prop.), IB-23C650 for limits high limit less 1.0%) LOC SETP INIT VAL XXX X (Low limit to high limit) PRESET VALUE XXXXXXX (.000 to 9999999)
POS PROP (Position prop.), RECOVERY OPTION MANUAL, LAST LIMIT IN MANUAL NO, YES=Limits apply in Manual SETPT 2 Entry point for set-point 2 FREDETRD COUNT XXXXXXX (.000 to 9999999)
HC/RR (Heat/Coo/, dual relay), POWER UP OUTP SRC LAST, FIXED SETPT 2 ENABLE NO, YES
HC/CR (HeatiCool, mA/relay), INPUT 2 SETUP Same steps as Process Input1 FIXED PWR UP OUTPT XX.X (-8.0 to 110.0, within Out- ALARMS **MENU**
HC/CC (Heat/Cool, dual mA), Setup thru Eng. Units Low put high and low limits) SETPT 2 FIXED Same steps as Set-point 1 BEEP ON OCCUR OF NONE, or any combination of:
ON/OFF (On,Off), I2 FAULT ACTION NONE, LOCAL (Controller put in Fixed thru Initial Value. DG, P1, P2
TIM PROP (Time pro port.) auto mode with fault value) RETRANS VARIABLE PROCESS, SETPOINT, Repeat for Set-points 3 and 4 ALARM ACK REQD ON NONE, or any combination of:
POS PROP has position choice NONE (Fix output 2 at 0 mA) POWER UP SETP SRC LAST, LOC SETPT. SETPT 2, DG, P1, P2
CONTROL ACTION DIRECT, REVERSE I2 FAULT VALUE XXXX (-3000 to 30000) RETRANS PROC HI XXXX (-3000 to 30000) Decimal SETPT 3, SETPT 4, REM SETP OVERCFGD DIAG ON YES , NO
MA. OUTP ACTION DIRECT, REVERSE I2 FAULT LEVL PCI XX (0 to 100%) or SETPT HI placed per "Inputs" Menu. INPUT 2 MISSING Warning message. times out in P1 RELAY ACTION LATCHING (relay releases
HEAT OUT ACTION DIRECT, REVERSE RETRANS PROC LO XXXX (-3000 to 30000) Decmal 1 second. when alarm acknowledged),
COOL OUT ACTION DIRECT, REVERSE ENG UNIT LABEL XXXX (X=any character in Tag or SETPT LO placed per "Inputs" Menu. FIXD PWR UP SETPT XXXX (-3000 to 30000, within NO LATCH (relay releases
VALVE CALIB See IB-23C650. Name field in Tune menu) local set-point limits) when alarm condition not
HOLD PWR UP MSG NO, YES (Hold ‘POWER RIGHT BAR OUTPUT (Output displayed) OUTPUT 2 MA. HIGH XX. X (01.0 to 54.0 mA dc) SETPOINT TRACKING NO, YES (Note: Remote set present)
FAILED’ message at startup) DEVIATN (Deviation displayed) OUTPUT 2 MA. LOW XX. X (0 to 53.0 mA point cannot track)
POWER UP MODE LAST, AUTO, MANUAL 0EV BAR FULL SCL XX (1 to 100% of span)
DISPLAYS AND ENTRIES
Top/Middle Display Bottom Display/Entry Top/Middle Display Bottom Display/Entry Top/Middle Display Bottom Display/Entry Top/Middle Display Bottom Display/Entry
RAT BIAS ENABLE NO, YES DIG INPT **MENU** RELAYS **MENU** RAMPSOAK **MENU*
The MODCELL 2050 generates display prompts to AUTOTUNE ENABLE NO, YES DIGITAL INPUT 1 Entry point for Digital Input 1. RELAY A SETUP Entry point for Relay A setup RAMPSOAK REPEAT NO, YES
make setup and operation fast and easy. The RAMPSOAK ENABLE NO, YES DIG IN 1 FUNCTION NONE, AUTO/MAN, ALRM ACK, RELAY A FUNCTION NONE, ALARMS, TOTALIZE, SOAK HYST XXXX (0 to 30000)
TOTALIZE ENABLE NO, YES TOTALIZE, RAMPSOAK, RAMPSOAK, REM/LOC, RAMP HYST XXXX (0 to 30000)
described below. The sequence of menus is RS-485 ENABLE YES, NO SETP SEL AUTO/MAN RAMPSOAK IS OFF For information only
TUNE PASSWORD XXXX (Enter this value [0 to DIG A-M OUT ENAB NO, YES RELAY A TRIP ACT On alarms 1, 2, 3, 4, 12, 13 or IS ON
more detailed information, see IB-23C650. 30000] in ‘Displays’ menu) DIG A-M OUT VAL XX.X (0 TO 54.0 mA) 14, 23, 24, 34, 123, 124, 134, RAMPSOAK UNIT TIM MINUTES, HOURS
CONFIG PASSWORD XXXX (Enter this value [0 to A/M KEY LOCKOUT YES, NO 234, 1234 RAMPSOAK SEGMENTS XX (0 to 10)
30000] in Displays menu) MAN-AUTO ALLOWED NO, YES RELAY B SETUP Same steps as Relay A Setup. SEG 1 SETUP Entry point for Segment 1
setup steps. CHK SUM DATABASE YES (ARE YOU SURE?), NO RAMPSOAK DI1 FUNC RUN/STOP, RUN/HOLD, RELAY C SETUP Same steps as Relay A Setup. SEG 1 START SP XXXX (Local Set-point Low Limit
See IB-23C650. RUN/SKIP (See IB-23C650) to Local Set-point High Limit)
Up: • Moves up through menus. DEFAULT DATABASE Up key requests default R/H, RSET LOCKOUT YES, NO (See IB-23C650 for RS-485 **MENU* See IB-23C650M SEG 1 END SP XXXX (Local Set-point Low Limit
• Increases values. LOCK CFG MENUS NO=Reaci access, YES or RUN/HOLD LOCKOUT explanation. RAT BIAS **MENU** to Local Set-point High Limit)