Atlas Sound AH5040S - Manual (Page 2)

1601 JACK MCKAY BLVD. ENNIS, TEXAS 75119 U.S.A.
TELEPHONE: (800) 876-3333
FAX (800) 765-3435
AtlasSound.com
2/4
©2008 Atlas Sound SL2-2048 ATS001850 RevE 1/08
Technical Specifications
Power Rating: 250 watts (45V) RMS
350 watts (53V) Peak
Sensitivity (1 W / 1 M): 104 dB SPL (70 Hz – 17 kHz 1 ⁄
3
octave
bands)
Frequency Response: 75 Hz - 17 kHz (±5 dB)
Dispersion: 50˚ x 40˚
Impedance: 8 Ω Nominal
Minimum Impedance: 5.6 Ω @ 9000 Hz Nominal -6 dB Minimum
Height: 23.75" (603.25 mm)
Width: 21.41" (543.81 mm)
Depth: 30.07" (763.78 mm)
Shipping Weight: 125 lbs (56.7 kg)
Driver Type: 1" HF & 15" LF
Architect & Engineer Specifications
Loudspeaker shall be Atlas Sound Model AH5040S or approved equal.
Loudspeaker shall be a 2-way design incorporating an environment-resis-
tant housing.
Loudspeaker shall include a 15", horn loaded, cast frame woofer housed
in a 2296 cubic inch (1.3 feet
3 ) enclosure and an integral, concentrically
mounted 1” exit compression driver coupled to a constant directivity
high frequency horn. The three pole (18 dB/octave) dividing network
crossover frequency shall be 1.4 kHz. The dividing network shall include
a poly switch protection circuit for the high-frequency component.
The loudspeaker system shall be capable of providing a sound dispersion
angle of 50˚ horizontal by 40˚ vertical in the 2 kHz octave band.
Rated power shall be 250 watts based on EIA Standard RS-426B*
Enclosure shall be UV-resistant, steel reinforced, low pressure injection
molded fiberglass and shall include a 3 stage multiple mesh filter system
for weather and rodent resistance:
A. Large 20-gauge perforated aluminum screen on front mouth
assembly.
B. 100 x 100 weave stainless steel mesh between HF horn and
HF driver.
C. 100 x 100 weave stainless steel mesh over 15" woofer.
Sensitivity shall be 104 dB SPL (75 Hz to 17 kHz 1 ⁄
3
octave bands) mea-
sured at a distance of one meter on axis with a one watt input.
Overall frequency response shall be 75 Hz to 17 kHz ( ±5 dB).
The loudspeaker shall include a stamped and formed, 12-gauge stainless
steel mounting bracket assembly for surface mounting and three M8
drop forged eyebolts for suspension mounting.
The input section located on the bottom rear of the loudspeaker shall
include a parallel wired 4 pole terminal block connector (1+ & 1- to input,
2+ & 2- provided as a through connection)
Nominal impedance shall be 8 Ω.
Dimensions shall be: Height: 23.75" (603.25 mm)
Width: 21.41" (543.81 mm)
Depth: 30.07" (763.78 mm)
Weight: 125 lbs (56.7 kg)
* EIA test spectrum is applied for eight hours.
(This procedure provides a rigorous test of both thermal and
mechanical failure modes.)
(21.41)
23.75
14.63
30.07
28.75
28.75"
(730.25 mm)
21.41"
(543.81 mm)
20.07"
(763.78 mm)
23.75"
(603.25 mm)
14.63"
(371.6 mm)