NetMedia MODLAMP-DI - Manual

MAN-MODLAMP REV1002A
NM-MODLAMP
NetMedia, Inc., 10940 N. Stallard Place, Tucson, Arizona 85737 (520) 544-4567 Fax: (520) 544-0800 Email: [email protected] www.netmedia.com
Modulated Camera
Indoor/Outdoor Weather Resistant
NM-MODLAMP
(SCM2 SCM3)
Elbow Bracket
Adjusts camera angle at base,
screw, and housing. Installs in
1/2” junction box covers.
Camera Lens
Comes prefocused from
factory but can be adjusted
by rotating in either direction.
Camera Bracket
Slot indicates image bottom.
Use slot to pull bracket out
and remove Modulator.
Housing
Available in Ivory only:
Model Camera Type
Base, Gasket & Screws
Mount to round 4” junction box.
Housing Cap
Remove to access Camera Lens,
Camera Bracket, and Modulator.
Locking Ring
Secures elbow bracket to
base at desired position.
(SCM2) NM-MODLAMP-CI
(SCM3) NM-MODLAMP-DI
Color
Day/Night Color
Video/Power Connector
Power and video share one coax
through female F connector.
Modulator
Not Shown - Behind Camera Bracket.
Switch bank sets output channel:
UHF 14-69 or CABLE 70-94, 100-125.
Power Injector
Connects power transformer to coax
for One Wire Video™ installation.
Modulator built into camera
One Wire Video™ installation
Combines with existing TV channels
Viewable on multiple televisions
Excellent image quality
Tough aluminum housing
Weather resistant enclosure
Internally routed cables
Mounts to standard electrical fixtures
Mounts directly to walls and ceilings
Works in low light conditions
Adjustable camera angles
Tamper resistant wiring
Includes power supply and power injector
One year limited warranty Camera Lens:
Image Sensor:
Resolution:
Field of View:
Min Illumination:
Infrared Sensitivity:
Modulation Method:
Output Channel:
Output Level:
Output Connector:
Cable Type:
Power Requirement:
Power Connector:
Housing Size:
Base Size:
Mounting Holes:
Weight:
Digital Crystal PLL
UHF 14-69, CABLE 70-94, 100-125
+30dBmV
Female F, 75 Ohm
RG59, RG6 or better
12V DC, 300mA
5.5mm OD, 2.1mm ID, center positive
2.13“ dia. x 3” long
4.5” dia., .75” high, 1/2“ hole
3.5” centers
1 lb.
(subject to change without notice)
FEATURES
Product Includes:
1. Camera Assembly (Camera, Modulator, Housing, Housing Cap, Elbow Bracket, Locking
Ring, Base, Gasket, Video/Power Connector).
2. Power Injector and 12V DC 300mA Power Transformer (Center Conductor Positive).
3. Mounting hardware (Mounting Screws, Grounding Strap, and Screw).
3.7mm
1/4” CCD
470 lines
54˚ Horizontal
0.5 Lux F1.2
No
The NetMedia MODLAMP (SCM2, SCM3) self contained camera and modulator converts its video signal to a selected televi-
sion channel. It is powered over the same coax cable that returns the video broadcast signal for One Wire Video™ installa-
tion. It mounts to a typical round 4 inch junction box and is viewed with a television tuner. Other junction boxes from your
local hardware store may also be used after replacing the round base with another that has a 1/2 inch diameter hole for the
elbow bracket. Equipment that does not have a tuner, such as a security monitor, Quad display, or DVR, will require a
demodulator (any TV tuner device with a composite video output such as a VCR) to convert the video for its use.
SPECIFICATIONS
Color Day/Night Color
3.6mm
1/3” CCD
540 lines
72˚ Horizontal
0.1 Lux
Yes
Color
Day/Night
Color