Control Company 5022 JUMBO TIMER - Manual

Specifications
Display:
LCD, 4-Digit 1”
Resolution: 1 second
Accuracy: ± 0.01%
Power: AAA battery
Size: 3¾ x 5½ X ½ inches
Accessories
Supplied:
Wall-mount bracket, stand, battery, Traceable®
Certificate, instructions.
Setting the Clock:
1.
Insert battery in battery compartment located on the back side of unit
2. To set clock, slide the CLOCK/TIMER switch to CLOCK. (1, Fig. 2).
3. Select 12 hour or 24-hour format (4, Fig. 2).
4. Slide SET/LOCK switch located on the back
of unit to SET. Press HR, MIN, and SEC
buttons until desired time is reached. Slide
SET/LOCK switch to LOCK position. See
Fig. 1, at right.
Counting up
1.
Place the unit in the clock mode by
sliding the CLOCK/TIMER switch to CLOCK.
(1, Fig. 2).
2. Press the START/STOP
button (2, Fig. 2) once to
begin counting up. Press
the START/STOP button a
second time to pause the
count (time-out). Press the
START/STOP button again
to resume counting. Any
number of timeouts may
be taken. Press CLEAR (3,
Fig. 2) while the count is
paused to reset the unit to
00:00:00.
3. The count-up is shown on
the lower portion of the
display. When 19:59:59 is
reached, the timer will return
to 00:00:00 and begin counting up again.
Counting Down
1.
Place the unit in the timer mode by sliding the CLOCK/TIMER switch to
TIMER. (1, Fig. 2). Slide the switch to T1 to set channel 1 and to T2 to
set channel 2. Slide SET/LOCK switch located on the back of unit to
SET. See Fig. 1.
2. Press HR, MIN, and SEC buttons until desired time is reached. Press
MEMORY button (4, Fig. 2) once. “MEMORY” will appear on the
display. Slide SET/LOCK switch to LOCK. recall stored time period,
press MEMORY button.
3. Press the START/STOP button (2, Fig. 2) once to start timing. Press
the START/STOP button a second time to pause the timing (time-out).
Press the START/STOP button again to resume timing. Any number of
time-outs may be taken. Press CLEAR (3, Fig. 2) while the timing is
paused to reset the unit to 00:00:00.
4. The upper portion of the display will show channel one. The lower
portion of the display will show channel two. To display both channels
simultaneously, slide the CLOCK/TIMER switch (1, Fig. 2) to the
TIMER 1 & 2 position.
5. When 00:00:00 is reached, the timer will alarm and begin counting up.
“TIME’S UP” will flash in the upper left portion of the display for the
appropriate channel. To silence the alarm and stop the count-up, press
the START/STOP button.
Low Battery
Erratic readings, a faint display, or no display are all indicators that the
battery is low and needs to be replaced. To replace the battery, remove the
battery cover located on the back of the unit and insert a new AAA battery.
Incorrectly installed batteries may damage electronics. Replace the Battery
Cover.
All Operational Difficulties
If this timer does not function properly for any reason, please properly
replace the battery with a new 1 .5V AAA alkaline battery (see Low Battery
section). Low battery power can occasionally cause any number of
“apparent” operational difficulties. Replacing the battery with a new fresh
battery will solve most difficulties.
Warranty, Service, or Recalibration
For warranty, service, or recalibration, contact:
CONTROL COMPANY
4455 Rex Road
Friendswood, Texas 77546 USA
Ph. 281-482-1714
Fax 281-482-9448
E-mail [email protected]
www.control3.com
Control Company is ISO 9001 Quality-Certified by
DNV and ISO 17025 accredited as a Calibration
Laboratory by A2LA.
Traceable ® is a registered trademark of Control Company
©2008 Control Company. 92-5022-00 Rev. 2 040808
TRACEABLE® JUMBO TIMER INSTRUCTIONS