Nova-Tech 5014 TRACEABLE EXTRA-EXTRA LOUD TIMER - Manual

WARRANTY, SERVICE, OR RECALIBRATION
For warranty, service, or recalibration contact:
CONTROL COMPANY
4455 Rex Road
Friendswood, Texas 77546 USA
Ph. 281-482-1714 Fax 281-482-9448
E-mail [email protected] www.control3.com
Control Company is
ISO 9001 Quality-Certified by DNV and ISO 17025
accredited as a Calibration Laboratory by A2LA.
Cat. No. 5014
Traceable ® Timer Instructions
92-5014-00
Rev. 1 052604
Traceable® is a registered trademark of Control Company
© 2004 Control Company
TRACEABLE ® EXTRA-EXTRA LOUD TIMER INSTRUCTIONS
SPECIFICATIONS
Display:
¾"-High LCD
Range: 99 hours, 59 minutes, 59 seconds
Accuracy: 0.01%
Alarm:
100 Decibel Audible and visual (distinct audible alarm for each channel)
Memory: Automatic recall of last programmed time (2 channels)
Functions: Countdown and count-up (stopwatch) timing
Features: Two independent timing channels Wall mount, magnetic back, and
stand
FEATURES
Liquid Crystal Display (LCD) - Timer display and clock. Clock displays as hour,
minutes and seconds in either a 12-hour or 24-hour format.
Clock button - Returns LCD to clock display
Clock Settings Buttons
Hour button - press to set hour function
Minute button - press to set minute function
Second button - press to set second functions
Timer Buttons - 2 independent timer buttons
Start/Stop Buttons - Starts and pauses T1 and T2
Alarm - Activates when timer returns to “0:00”
Battery Compartment for Buzzer Alarm - Holds two “AAA” size batteries
Battery Compartment for Clock Timer - Holds one silver oxide battery
Recessed Wall-mount Holes - Use to mount on wall or vertical surface
Magnetic Mounts - Use to mount on a metal surface
Retractable Table Stand - Use for setting on a horizontal surface
NORMAL TIME SETTING
1. Press “Clock” button for approximately 3 seconds. Display time will flash.
2. Press “H” button to reset hour setting.
NOTE: press and hold time setting buttons for approximately 2 seconds for
rapid acceleration of time setting.
3. The letter “P” will appear in the display below
the colon to designate PM. No designation indicates AM.
4. Press “M” button to set minute setting.
5. Press “S” button to set seconds setting. When digits are between 00 to 29,
setting will return to zero. Pressing “S” button when digits are between 30 to
59, range will advance to next minute.
6. Press ‘Clock” button to start clock. Colon will flash in clock mode.
7. Clock operates independently of timing channels. Whenever “CLOCK”
button is pressed, current time will appear in the display.
12/24 HOUR FORMAT SELECTION
1. To activate 24-hour format, in Clock Mode press and hold START/STOP
button for approximately 3 seconds. A beep tone will indicate format change.
2. To change back to 12-hour format, repeat step 1.
COUNT-DOWN TIMER SETTING
Example: T1 with 3 hour, 18 minutes and 22 seconds
1. Press “T1” button to select the desired timer. The selected timer will appear
in the display. Colon does not flash in timer mode.
2. Press “C” to clear the timer and reset to zero.
3. Press “H”, “M”, or “S” buttons to set timer. Rapid acceleration of digits can
be achieved by holding the individual buttons down for 2 seconds.
4. If programming error occurs, hold respective “H”, “M”, or “S” button down first,
simultaneously press “C” button to clear digit. Reprogram as explained above.
5. Follow same procedure above for programming timer channel T2.
6. Press “START/STOP” button to activate timer. When both timers are active,
the timer being viewed will be indicated by a “T1” or “T2” display that is not
flashing. Active, non-displayed timer will be indicated by a flashing indicator.
7. When a displayed timer is actively timing, press START/STOP button and
displayed timer will pause.
8. Press START/STOP button again and timing will resume.
TIMER BUZZER ALARM
1. When timer reaches 00:00:00, timer buzzer alarm will activate and timer will
proceed to count up in seconds.
2. Stop timer buzzer by pressing any button.
3. Buzzer will automatically stop after 60 seconds. The count-up timer
continues to operate until stopped.
4. Count-up timer, in alarm mode, can be stopped by pressing any button.
5. Press “C” button to reset display to zero.
6. If both timers are active, and each expires within a minute of each other, the
alarm will activate for one minute following the expiration of the first alarm.
7. Both timers will proceed to count upwards once the respective timer has
reached 00:00:00.
8. Press START/STOP button to turn off.
TIMER MEMORY RECALL
1. After timer buzzer alarm and timer stop (do not press “C”), press “START/
STOP” button to recall the preset timer time.
2. Press “START/STOP” button again to start timer.
NOTE: Both timers can be used at same time. When using both timers, press
“T1” or “T2” button to display each timer.
COUNT-UP/STOPWATCH TIMER
1. Press “T1” or “T2” button.
2. Press “CLEAR” button to clear display.
3. Press “START/STOP” button, timer will begin.
4. Press START/STOP to stop the timer.
5. To restart, press START/STOP button again.
6. To deactivate, press START/STOP button, then press “CLEAR” button.
WALL-MOUNT RECESS HOLES
Located on the back side of the unit.
MAGNETIC ATTACHMENT
The timer can be attach to iron or steel surfaces, using the magnet attached to
clip on backside of timer.
TABLE TOP USE
Use the retractable table stand to set the unit on a flat surface such as a bench
top.
BATTERY REPLACEMENT
Clock Alarm Battery
Replace battery when low. Open battery compartment located behind
retractable table stand by unscrewing battery compartment door. Replace with
one silver-oxide battery (Control Company Cat. No. 1039).
Buzzer Alarm Battery
The buzzer alarm has separate batteries. To replace the buzzer alarm batteries,
open the battery door by gently pressing and pushing the center of the door.
Insert two “AAA” size batteries (Control Company Cat. No. 1105)
NOTE: The timer will continue to function without buzzer batteries being
installed. However, if these batteries are not installed, the buzzer alarm
will not function.
ALL OPERATIONAL DIFFICULTIES
If this timer does not function properly for any reason, please replace the
batteries with new, high-quality batteries (see “Battery Replacement” section).
Low battery power can occasionally cause any number of “apparent” opera-
tional difficulties. Replacing the batteries with new, fresh batteries will solve most
difficulties.
MAINTENANCE - When handled properly, this unit is engineered to give years
of satisfactory service. Here are a few product care instructions:
1. Do not immerse unit in water. IF unit comes in contact with water, dry unit
immediately with soft, lint-free cloth.
2. Do not clean unit with abrasive or corrosive materials. Abrasive cleaning
agents may scratch the plastic parts and corrode the electronic circuit.
3. Do not subject the unit to excessive: force, shock, dust, temperature, or
humidity. Such treatment may result in malfunction, a shorter electronic life
span, damaged batteries, or distorted parts.
4. Do not tamper with unit’s internal components. Doing so will terminate unit’s
warranty and may cause damage. Unit contains no
user-serviceable parts.
5. Only use new batteries as specified in this instruction manual. Do not mix
new and old batteries as the old batteries may leak.