Control Company 3388 VARIABLE-FLOW CHEMICAL TRANSFER PUMP - Manual

VARIABLE-FLOW CHEMICAL TRANSFER PUMP
CONTROL COMPANY
4455 Rex Road Friendswood, Texas 77546 USA
Ph. 281 482-1714 Fax 281 482-9448
E-mail [email protected] www.control3.com
Control Company is ISO 9001 Quality-Certified by DNV and ISO 17025 accredited as a Calibration Laboratory by A2LA.
Cat. No. 3388 Variable Flow Chemical Transfer Pump Instructions
92-3388-00
Rev. 5 122707
Traceable ® is a registered trademark of Control Company.
© 2006 Control Company
SPECIFICATIONS:
Flow: 120 milliliters to 2.2 liters per minute
Fluid Viscosity: 0 to 200 centipoises
Suction Lift: 3 meters wet, 10 centimeters dry
Acceptable Fluid
Temperatures:
–40 to 93 o C
Acceptable Tubing: All types
Tubing Size: Inside diameter of nominal 4.8 mm
(
3 /
16
inch)
Wetted Parts: Dupont Delrin, 304 Stainless Steel, Viton, Dupont Teflon
Motor: 12 Volt DC Variable
Adaptor: U.L. 120 VAC, 60 Hz, 47 W
Duty cycle: Intermittent
Size: 20.3 x 12 x 11.5 cm (8 x 4 ¾ x 4 ½ inches)
Weight: 454 grams (1 pound)
CAUTION: Prior to use, a 'Chemical Resistance Chart' should be used to insure
that wetted pump parts will not be affected by chemical being pumped.
MAXIMUM FLOW RATES AT DIFFERENT HEAD PRESSURES
PSI Ft H20 ml/min fluid oz/min
0 0 2,200 78
5 12 2100 75
10 23
1750 63
15 35 1250 45
20 46 350 13
CONTROL PANEL
S1: Power/Direction switch: For selecting FORWARD, REVERSE, & power OFF
S2: Pump Speed switch: For selecting FAST, SLOW, and PRIME (PURGE)
C1: Variable Flow Control: For varying flow rate
CAUTION: During operation of the pump, the top panel or the black heat sink
on the back of the pump may be very warm to the touch.
OPERATION
1. Plug
the power supply into an electrical outlet.
2. Remove red covers from the inlet and outlet barbed pump fittings.
3. NOTE: To insure instant pumping place some liquid into pump inlet or outlet
fittings so it is wetted. (Prime pump by placing some liquid into the
barbed fitting. This can be done by squeezing a short piece of tubing
filled with liquid, an eyedropper, a bulb filled with liquid, blowing into
a short piece of tubing filled with liquid, or using a syringe.)
4. Slide one end of a piece of tubing nominal 4.8 mm, inside diameter
( 3 /
16
-inch) over the barbed inlet pump fitting. Most users select nomi-
nal 4.8 mm ( 3 /
16
”) inside diameter tubing. Place the other end of the
tubing into the vessel to be emptied.
5. Slide one piece of tubing over the barbed outlet pump fitting. Place
the other end of the tubing into the vessel to be filled.
6. Move Power/Direction switch (S1) to FORWARD to activate
pumping.
7. Move the Pump Speed switch (S2) to Prime (Purge) to quickly fill
the tubing with liquid.
8. Move the Pump Speed switch (S2) to SLOW or FAST.
9. Within each of the two speed ranges (SLOW and FAST), the flow
rate can be varied for precise delivery by rotating the Variable Flow
Control knob (C1). Selecting a higher reference number increases
the flow rate of the pump.
10. Use REVERSE (S1) to empty the liquid in the tubing back to a
vessel.
TROUBLESHOOTING
1. If
the pump sounds like it is pumping, but no liquid is moving, do
the following. Prime the pump by placing some liquid into the
barbed inlet fitting. This can be done by squeezing a short piece of
tubing filled with liquid, an eyedropper, a bulb filled with liquid,
blowing into a short piece of tubing filled with liquid, or using a
syringe.
2. If the pump has been pumping at high speed for sometime, the
regulator chip may overheat and shut the unit down. Turn the pump
off and allow it to cool down.
3. If the pump makes no sound when turned on, make certain there is
power to the outlet and the power supply is plugged in.
ACCESSORIES
Control Co.
Cat. No. 3280 Tight-Seal
TM Hose/Tubing Clamp Assortment
Includes 5 each of 13 different sizes. Clamps have an inside diameter
from 6.2 mm to 41 mm (0.246 to 1.61 inches). Clamps securely fasten
tubing on connectors, pumps, glassware, and filtration units. Chemi-
cal-corrosion-resistant, rustproof, and nonconducting nylon is ideal for
use in the wide temperature range of 0 to 90
o C (32 to 194 o F).
Control Co.
Cat. No. 3285 Tight-Ties
TM , Cable Ties Assortment
Includes 400 ties with lengths from 4 to 14 inches. One-piece, self-
locking, ties are made of chemical-corrosion-resistant, rustproof, and
nonconducting nylon, ideal for use in the wide temperature range of
–40 to 85 o C (-40 to 185 o F).
WARRANTY OR SERVICE
For warranty or service, contact: