Control Company 4126 BIG-DIGIT MEMORY THERMOMETER - Manual

Traceable ® is a registered trademark of Control Company ©2008 Control Company. 92-4126-00 Rev. 3 052008
SPECIFICATIONS
Display: 1⅛ inch (2.86 cm) LCD
Range— Ambient: 23.0 to 122.0 °F (–5.0 to 50.0 °C)
Probe: –58.0 to 158.0 °F (–50.0 to 70.0 °C)
Resolution: 0.1°
Accuracy: ±1°
Sampling Time: 10 seconds
Power: 1 AAA Alkaline Battery
Case: ABS Plastic
Size: 2¾ x 4¼ x ⅝ inches
Accessories: sensor bracket, Velcro™, stand, battery, Traceable ® Certificate.
FIGURE 1: DESCRIPTION
1. Ambient Display
2. Probe Display
3. Maximum (MAX) Temperature Button
4. Minimum (MIN) Temperature Button
5. RESET Button
6. Probe
NOT SHOWN
°C/°F Switch on back of unit
OPERATION
1.
Turn the thermometer on by inserting the battery. To insert the battery, slide the
Battery door located on the back in the direction of the arrow. Insert the battery
as directed by the polarity symbols (+ and -). Replace the Battery Door.
2. The external probe may be used to monitor temperatures in air/gas, liquids, and
semi-solids. Both the probe and cable may be totally immersed in water.
3. Select Fahrenheit (°F) or Celsius (°C) by sliding the switch on the back of the
unit to the desired setting.
4. Press the RESET button. All segments will be displayed for 3 seconds then the
unit will display the current °F or °C temperature.
MEMORY
1. Press the MIN or MAX button once to recall both the ambient and probe
minimum/maximum temperature. “MIN” or “MAX” will appear on the display.
2. Press the MIN or MAX button once again to return to the current temperature
display. “MIN” or “MAX” will no longer appear on the display.
3. With “MIN” or “MAX” on the display, press the RESET button to reset either the
minimum and maximum temperatures. All segments will be displayed for 3
seconds and the minimum or maximum temperatures will be set to the current
temperature.
DISPLAY MESSAGES
HHH (Flashing)— Indicates that the temperature being measured is above the range
of the unit.
LLL (Flashing)— Indicates that the temperature being measured is below the range
of the unit.
MOUNTING
A wire holder is provided with the external probe for permanent mounting. To mount
the probe, place a screw or nail through the hole of the wire holder and secure the
holder to the wall. The unit is provided with a receptacle for wall mounting. Set a screw
into the wall at the location desired. The head of the screw will need to slip into the
receptacle on the back of the unit. Do not set the screw flush to the wall. Once the
screw has been set properly, hang the unit in place by sliding the receptacle on the
back of the unit over the head of the screw. The unit may also be mounted by using
the Velcro
™ supplied.
BENCH STAND
The unit is supplied with a bench stand that is a part of the case. To use the bench
stand, locate the small rectangular opening on either side of the battery cover. Place
your finger nail into the opening and flip the stand up. To close the stand, simple snap
it shut.
BATTERY REPLACEMENT
Erratic readings, a faint display, or no display are all indicators that the battery is low
and must be replaced. To replace the battery, slide Battery Door located on the back
in the direction of the arrow. Insert a new 1.5V AAA alkaline battery, NOT a regular or
heavy duty battery, as directed by the polarity symbols (+ and -). Incorrectly installed
batteries may damage electronics. Replace the Battery Door.
ALL OPERATIONAL DIFFICULTIES
If this thermometer does not function properly for any reason, please replace the
battery with a new high quality battery (see “Battery Replacement” section). Low
battery power can occasionally cause any number of “apparent” operational difficulties.
Replacing the battery with a new fresh battery will solve most difficulties.
WARRANTY, SERVICE, OR RECALIBRATION
For warranty, service, or recalibration, contact:
CONTROL COMPANY
4455 Rex Road
Friendswood, Texas 77546 USA
Ph. 281-482-1714 Fax 281-482-9448
E-mail [email protected]
www.control3.com
Control Company is ISO 9001 Quality-
Certified by DNV and ISO 17025 accredited
as a Calibration Laboratory by A2LA.
TRACEABLE ® BIG-DIGIT MEMORY THERMOMETER INSTRUCTIONS