Control Company 4147 ALARM THERMOMETER/ALARM TIMER - Manual

SPECIFICATIONS
Display:
3 /
4
” digits, 1 1 /
2
” LCD
Range: 32 to 392 o F and 0 to 200 o C
Resolution: 1 o
Accuracy:
±
2 o C
Sampling Rate: 1 second
Size/Weight: 2 3 /
4
x 3 x 1 /
2
” / 4.2 oz
Alarm: Audible, distinct alarm sound for both
temperature and time
Features: Probe – 0.16” dia. x 8 1 /
2
” length
Cable – 42” length
Adjustable viewing angle
CONTROLS/INDICATORS
START/STOP - Starts and stops timer operation
HR - Sets hours for timer feature
MIN - Sets minutes for timer feature
CLEAR - Clears timer display
UP - Increases degree increment of alarm
DOWN - Decreases degree increment of alarm
TEMP ALERT ON/OFF - Turns temperature alarm on/off.
o F/ o C (on back of unit) - Switches from Farenheit to Celsius
TIMER OPERATION
1. Reset the display to 0:00 by simultaneously pressing the
HR and MIN buttons (timer must be stopped to reset).
2. Press the HR button to advance the hours to the desired
setting. Press the MIN button to advance the minutes to
the desired setting. An audible beep confirms each entry.
You may rapidly advance the hours or minutes by holding
down the HR or MIN button.
3. When the timer is set, press the START/STOP button to
start countdown alarm operation.
4. If a pause in timing operation is required press the
START/STOP button to “freeze” the display at the current
reading (time-out). To resume time at the point it was
stopped, press the START/STOP button again. An
unlimited number of timeouts may be taken.
5. When the timer reaches zero a 1-minute alarm sounds, a
“TIME’s-UP” message is displayed and the timer begins
counting up.
6. Press the START/STOP button to silence the alarm and
return the display to it’s previously programmed setting.
NOTE: The timer and temperature alarm are easily recogniz-
able by two distinct alarm sounds.
THERMOMETER OPERATION
1. Connect the probe jack to the outlet on the left side of the
unit’s stand. Insert the probe tip in the material to be
measured.
NOTE: The probe may be used to monitor temperatures in
air/gas, liquids and semisolids.
NOTE: The probe cable is not waterproof. Do not immerse
the probe cable in liquid. Immersing the probe cable in
liquid can cause permanent damage to the thermometer.
2. Slide the o F/ o C switch to o F to display the temperature in
Fahrenheit or to o C to display the temperature in Celsius.
3. Slide the TEMP ALERT switch to ON. An “ALERT”
message is displayed indicating the temperature alarm is
on.
4. Set the temperature alarm in 1 o increments by scrolling
UP or DOWN using the TEMP SET buttons.
5. When the temperature reading, as measured at the probe,
matches or is higher than the temperature alarm setting a
5-minute alarm sounds. The temperature alarm can be
temporarily silenced by pressing the START/STOP button.
If the temperature remains above the alarm setpoint a 5
second reminder alarm will continue to sound every
minute. To turn the temperature alarm off, slide the TEMP
ALERT switch to the OFF position.
NOTE: The timer and temperature alarm are easily recogniz-
able by two distinct alarm sounds.
ALL OPERATIONAL DIFFICULTIES
If this unit does not function properly for any reason, replace
the battery with a new high-quality battery (see “Battery
Replacement” section). Low battery power can occasionally
cause any number of “apparent” operational difficulties.
Replacing the battery with a new fresh battery will solve most
difficulties.
BATTERY REPLACEMENT
Erratic readings, a faint display, no display or flashing display
are all indicators that the battery must be replaced. Remove
the battery compartment panel that is located on the under-
side of the unit and replace the exhausted battery with a new
alkaline AAA battery. With the battery securely in place,
replace the compartment cover. Replacement battery Cat.
No. 1105.
WARRANTY, SERVICE OR RECALIBRATION:
For warranty, service or recalibration contact:
TRACEABLE  ALARM THERMOMETER/
ALARM TIMER INSTRUCTIONS
CONTROL COMPANY
4455 Rex Road
Friendswood, TX 77546 USA
Ph. 281-482-1714 Fax 281-482-9448
E-mail [email protected]
www.control3.com
Control Company is ISO 9001 Quality-Certified by DNV
and ISO 17025 accredited as a
Calibration Laboratory by A2LA.
Cat. No. 4147
Traceable® Alarm Thermometer/Alarm Timer Instructions
92-4147-00
Rev 1 071204
Traceable® is a registered trademark of Control Company
© 2004 Control Company