Pach and Company AeGIS 7000P Series Quick Guide - Manual

 Missing Parts, contact Pach and Company 1-888-678-7224
 Defective system under manufacturer warranty,
call 1-888-678-7224 for advance replacement

24 Months warranty for complete system
 6 Months warranty for Printed Circuit Board
What is Master Code: 4- digit code to log-on to programming
mode (0000 is default)
What is Dir (directory code): 2, 3, or 4 digit number see function
code 09. The number can be associated to apartment no., first
three digit of phone no., last four digit of phone no. , or any random
no. assigned to each tenants. Every tenant must have different
directory code no..
What is Access Code: 4-digit code for tenant to open the door or
gate.
Exit program, clear field,
reset keystroke.
46
Display system’s
information
Save program 50
Clear memory to
factory default
00
Change master code
(0000 is default)
51
Enable Phone Bill
Must be set to 0
01 Add new tenant 70
Change talk time
(010-180 seconds)
60 seconds is default
02 Edit existing tenant 71
Change door open
interval (04-99
seconds)
03 Delete existing tenant 72
Invalid code lock-out
count (1-9). 3 is
default
04 Clear all tenants 73 N/A
05
Manual unlock/lock relay
1 with timer (01-98 hours,
99 hours unlock hold, 00
hours to lock)
74
Enable/disable auto
answer. Enable is
default
06
Directory Digit
Select 2, 3 or 4 digit
Default= 3-digit
75
Enable/disable
keypad press beep.
Enable is default
07
Single or multi system
(single is default)
76
Enable/disable
speaker beep.
Enable is default
08 System ID number (n/a) 77
Enable/disable PBX.
Disable is default
10 Edit scrolling message 78
View name and
directory
40 Master code mask.
Warning: Master code
cannot be recovered if
masked. Board must be
replaced.
91 Total number of
tenant. Tenant with
no name will not be
included
Log on to programming: Press
simultaneously then release, the
welcome message will stop scrolling
(repeat if screen still scrolls) enter 4-digit
“
MASTER CODE ” (0000 is default), the
screen will show:
Select the “ Function Code ” from the table
Two ways call from the system
1. Press to scroll name from A-Z or to scroll name from
Z-A then press to call name selected.
2. Press wait for dial tone then press the directory no.
Opening the door remotely press
Opening the door using the access code press (display
screen will stop scrolling) then press a valid 4-digit access
code.
Extending talk time tenant must press from the phone
after the time out warning beep.
Calling into the system : incase you are not available when
your visitor call you. Follow steps below to use this feature
1. Function 74 (auto answer must be enabled).
2. Call the system’s phone no., you will hear “TWO BEEP”, then
press to talk to your visitor. Press to release the
door
Enable PBX : if the system is connected to one of the PBX
extension and 9 is required to call an outside line, then enable
the PBX using function code 77. Select pause between 1-5
seconds.
HOW TO ENTER A CHARACTER
1. Press the associated button to enter a character then
2. Press
3. You have 30 seconds to enter each letter or character.
4. Letter QZ, numeric 0-9 and punctuations press
5. Press space and for backspace
PACH AND CO 1-888-678-7224 Quick Guide
WARNING:
DO NOT USE ON BOARD
12VDC and GND TO POWER A DOOR STRIKE
OR MAGNETIC LOCK
SEPARATE POWER MUST BE USED TO
POWER A DOOR STRIKE OR MAGNETIC
LOCK.
TECHNICAL SUPPORT IS AVAILABLE MON-FRI
7:30AM-3:30PM PST AT 1-888-678-7224